BSDL Files Library for JTAG

The only free public library that contains thousands of BSDL (Boundary Scan Description Language) models to use with BScan/JTAG tools

BSDL model: XC4006E_PG156

--$ XILINX$RCSfile: xc4006e_pg156.bsd,v $
--$ XILINX$Revision: 1.4 $
--
-- BSDL file for device XC4006E, package PG156
-- Xilinx, Inc. $State: FINAL $ $Date: 2002-01-29 14:38:41-08 $
-- Generated by createBSDL 2.6
--
-- For technical support, contact Xilinx as follows: 
-- North America 1-800-255-7778 hotline@xilinx.com 
-- United Kingdom +44 870 7350 610 eurosupport@xilinx.com
-- France  (33) 1 3463 0100 eurosupport@xilinx.com
-- Germany  (49) 89 991 54930 eurosupport@xilinx.com
-- Japan  (81) 3-3297-9163 jhotline@xilinx.com
--
-- BSDL verified to conform to 1149.1b-1994 syntax. This device has been 
-- tested by the Intellitech 1149.1 Verification Lab using the Intellitech
-- Eclipse(TM) Scan Diagnostic Tool and the Intellitech RCT(TM). This
-- device has been verified to operate according to the BSDL provided,
-- and is compatible with the IEEE 1149.1 standard when the operating 
-- instructions in the BSDL are followed. 
-- PH: 603-868-7116 or email: scansupport@intellitech.com
--
-- This BSDL file reflects the pre-configuration JTAG behavior. To reflect
-- the post-configuration JTAG behavior (if any), edit this file as described
-- below. Many of these changes are demonstrated by commented-out template
-- lines preceeding the lines they would replace:
-- 	
-- 1. Enable USER instructions as appropriate (see below).
-- 2. For inputs using uncontrolled paths (e.g. PGCK, SGCK), change
-- 	boundary cell function from 'input' to 'clock' or 'observe_only'.
-- 3. Set disable result of all pads as configured.
-- 4. Set safe state of boundary cells as necessary.
-- 5. Set safe state of INIT output to X, or as necessary (see below).
-- 6. Rename entity if necessary to avoid name collisions.
-- 7. Change INIT port direction from "in" to "inout" (see below).
-- 8. Change COMPLIANCE_PATTERNS to "(PROGRAM) (1)" (see below).
-- 9. Change INIT boundary cells from internal to controlr, output3,
-- 	and input, respectively (see below).
-- 10. Remove the design warning regarding keeping INIT low.
-- 
-- NOTE: Post-configuration JTAG is available only if the BSCAN symbol
-- 	is instantiated in the FPGA design.
-- NOTE: PULLUP symbols must be instantiated on the TMS and TDI pins
-- 	in the FPGA design to comply with IEEE Std. 1149.1-1993.

entity XC4006E_PG156 is

generic (PHYSICAL_PIN_MAP : string := "PG156" );

port (
	CCLK: linkage bit;
	DONE: linkage bit;
	GND: linkage bit_vector (1 to 16);
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the following line so
-- that INIT is of type inout.
-- 	INIT: inout bit;
	INIT: in bit; 
	IO2: inout bit;
	IO3: inout bit;
	IO4: inout bit;
	IO5: inout bit;
	IO6: inout bit;
	IO7: inout bit;
	IO8: inout bit;
	IO9: inout bit;
	IO11: inout bit;
	IO12: inout bit;
	IO13: inout bit;
	IO14: inout bit;
	IO15: inout bit;
	IO16: inout bit;
	IO17: inout bit;
	IO18: inout bit;
	IO22: inout bit;
	IO23: inout bit;
	IO24: inout bit;
	IO25: inout bit;
	IO28: inout bit;
	IO31: inout bit;
	IO32: inout bit;
	IO34: inout bit;
	IO35: inout bit;
	IO36: inout bit;
	IO37: inout bit;
	IO38: inout bit;
	IO41: inout bit;
	IO42: inout bit;
	IO43: inout bit;
	IO44: inout bit;
	IO45: inout bit;
	IO46: inout bit;
	IO47: inout bit;
	IO48: inout bit;
	IO50: inout bit;
	IO52: inout bit;
	IO53: inout bit;
	IO54: inout bit;
	IO55: inout bit;
	IO56: inout bit;
	IO57: inout bit;
	IO63: inout bit;
	IO64: inout bit;
	IO65: inout bit;
	IO66: inout bit;
	IO67: inout bit;
	IO68: inout bit;
	IO69: inout bit;
	IO70: inout bit;
	IO72: inout bit;
	IO73: inout bit;
	IO74: inout bit;
	IO75: inout bit;
	IO76: inout bit;
	IO77: inout bit;
	IO78: inout bit;
	IO82: inout bit;
	IO83: inout bit;
	IO84: inout bit;
	IO85: inout bit;
	IO86: inout bit;
	IO87: inout bit;
	IO88: inout bit;
	IO89: inout bit;
	IO91: inout bit;
	IO92: inout bit;
	IO93: inout bit;
	IO94: inout bit;
	IO95: inout bit;
	IO96: inout bit;
	IO97: inout bit;
	IO98: inout bit;
	IO103: inout bit;
	IO104: inout bit;
	IO105: inout bit;
	IO106: inout bit;
	IO107: inout bit;
	IO108: inout bit;
	IO109: inout bit;
	IO110: inout bit;
	IO112: inout bit;
	IO113: inout bit;
	IO114: inout bit;
	IO115: inout bit;
	IO116: inout bit;
	IO117: inout bit;
	IO118: inout bit;
	IO119: inout bit;
	IO122: inout bit;
	IO123: inout bit;
	IO124: inout bit;
	IO125: inout bit;
	IO126: inout bit;
	IO127: inout bit;
	IO128: inout bit;
	IO129: inout bit;
	IO131: inout bit;
	IO133: inout bit;
	IO134: inout bit;
	IO135: inout bit;
	IO136: inout bit;
	IO137: inout bit;
	IO138: inout bit;
	IO143: inout bit;
	IO144: inout bit;
	IO145: inout bit;
	IO146: inout bit;
	IO147: inout bit;
	IO148: inout bit;
	IO149: inout bit;
	IO150: inout bit;
	IO152: inout bit;
	IO153: inout bit;
	IO154: inout bit;
	IO155: inout bit;
	IO156: inout bit;
	IO157: inout bit;
	IO158: inout bit;
	IO159: inout bit;
	M0: in bit;
	M1: inout bit;
	M2: in bit;
	PROGRAM: in bit;
	TCK: in bit;
	TDI: in bit;
	TDO: out bit;
	TMS: in bit;
	VDD: linkage bit_vector (1 to 8)
); --end port list

use STD_1149_1_1994.all;

attribute COMPONENT_CONFORMANCE of XC4006E_PG156 : entity is
	"STD_1149_1_1993";

attribute PIN_MAP of XC4006E_PG156 : entity is PHYSICAL_PIN_MAP;

constant PG156: PIN_MAP_STRING:=
	"CCLK:R2," &
	"DONE:R15," &
	"GND:(F3,C4,C6,C8,C11,C13,F14,J14,L14,P14," &
		"P11,P8,P6,N3,L3,H2)," &
	"INIT:H15," &
	"IO2:H1," &
	"IO3:G1," &
	"IO4:G2," &
	"IO5:G3," &
	"IO6:F1," &
	"IO7:F2," &
	"IO8:E1," &
	"IO9:E2," &
	"IO11:D1," &
	"IO12:D2," &
	"IO13:E3," &
	"IO14:C1," &
	"IO15:C2," &
	"IO16:D3," &
	"IO17:B1," &
	"IO18:B2," &
	"IO22:B3," &
	"IO23:A1," &
	"IO24:A2," &
	"IO25:C5," &
	"IO28:A4," &
	"IO31:B5," &
	"IO32:B6," &
	"IO34:C7," &
	"IO35:B7," &
	"IO36:A6," &
	"IO37:A7," &
	"IO38:A8," &
	"IO41:C9," &
	"IO42:B9," &
	"IO43:A9," &
	"IO44:B10," &
	"IO45:C10," &
	"IO46:A10," &
	"IO47:A11," &
	"IO48:B11," &
	"IO50:A12," &
	"IO52:B12," &
	"IO53:A13," &
	"IO54:A14," &
	"IO55:C12," &
	"IO56:B13," &
	"IO57:B14," &
	"IO63:B16," &
	"IO64:D14," &
	"IO65:C15," &
	"IO66:D15," &
	"IO67:E14," &
	"IO68:C16," &
	"IO69:E15," &
	"IO70:D16," &
	"IO72:F15," &
	"IO73:E16," &
	"IO74:F16," &
	"IO75:G14," &
	"IO76:G15," &
	"IO77:G16," &
	"IO78:H16," &
	"IO82:J15," &
	"IO83:J16," &
	"IO84:K16," &
	"IO85:K15," &
	"IO86:K14," &
	"IO87:L16," &
	"IO88:M16," &
	"IO89:L15," &
	"IO91:N16," &
	"IO92:M15," &
	"IO93:P16," &
	"IO94:M14," &
	"IO95:N15," &
	"IO96:P15," &
	"IO97:N14," &
	"IO98:R16," &
	"IO103:T16," &
	"IO104:T15," &
	"IO105:R13," &
	"IO106:P12," &
	"IO107:T14," &
	"IO108:T13," &
	"IO109:R12," &
	"IO110:T12," &
	"IO112:R11," &
	"IO113:T11," &
	"IO114:T10," &
	"IO115:P10," &
	"IO116:R10," &
	"IO117:T9," &
	"IO118:R9," &
	"IO119:P9," &
	"IO122:T8," &
	"IO123:T7," &
	"IO124:T6," &
	"IO125:R7," &
	"IO126:P7," &
	"IO127:T5," &
	"IO128:R6," &
	"IO129:T4," &
	"IO131:R5," &
	"IO133:T3," &
	"IO134:P5," &
	"IO135:R4," &
	"IO136:R3," &
	"IO137:P4," &
	"IO138:T2," &
	"IO143:R1," &
	"IO144:P2," &
	"IO145:N2," &
	"IO146:M3," &
	"IO147:P1," &
	"IO148:N1," &
	"IO149:M2," &
	"IO150:M1," &
	"IO152:L2," &
	"IO153:L1," &
	"IO154:K3," &
	"IO155:K2," &
	"IO156:K1," &
	"IO157:J1," &
	"IO158:J2," &
	"IO159:J3," &
	"M0:A16," &
	"M1:A15," &
	"M2:B15," &
	"PROGRAM:R14," &
	"TCK:A3," &
	"TDI:B4," &
	"TDO:T1," &
	"TMS:A5," &
	"VDD:(H3,C3,B8,C14,H14,P13,R8,P3)";
--end pin map

attribute TAP_SCAN_IN    of TDI : signal is true;
attribute TAP_SCAN_MODE  of TMS : signal is true;
attribute TAP_SCAN_OUT   of TDO : signal is true;
attribute TAP_SCAN_CLOCK of TCK : signal is (2.0e6, LOW);
-- This is conservative. Real max is expected to be (~5MHz, BOTH).

attribute COMPLIANCE_PATTERNS of XC4006E_PG156 : entity is
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the corresponding line
-- below.
-- 	"(PROGRAM) (1)";
-- 
-- NOTE: If INIT has been high or floating since the later of power-on
-- 	and the last rising transition of PROGRAM, then the device may
-- 	be in configuration mode in which case some JTAG instructions
-- 	will not be available.
	"(INIT,PROGRAM) (01)"; 

attribute INSTRUCTION_LENGTH of XC4006E_PG156 : entity is 3;

attribute INSTRUCTION_OPCODE of XC4006E_PG156 : entity is
	"SAMPLE (001)," & -- Internal capture not valid until after config
	"RESERVED (110)," &
	"READBACK (100)," & -- Not available during configuration
	"CONFIGURE (101)," & -- Not available during configuration
	"USER2 (011)," & -- Not available until after configuration
	"USER1 (010)," & -- Not available until after configuration
	"EXTEST (000)," & -- Not available during configuration
	"BYPASS (111)";

attribute INSTRUCTION_CAPTURE of XC4006E_PG156 : entity is "X01";
-- MSB of instruction capture is low during configuration.

-- If the device is configured, and a USER instruction is implemented
-- and not private to the FPGA designer, then it should be removed
-- from INSTRUCTION_PRIVATE, and the target register should be defined
-- in REGISTER_ACCESS.

attribute INSTRUCTION_PRIVATE of XC4006E_PG156 : entity is
	"USER1," &
	"USER2," &
	"READBACK," &
	"RESERVED," &
	"CONFIGURE";

attribute REGISTER_ACCESS of XC4006E_PG156 : entity is
--	"<reg_name>[<length>] (USER1)," &
--	"<reg_name>[<length>] (USER2)," &
	"BYPASS (BYPASS)," &
	"BOUNDARY (SAMPLE,EXTEST)";

attribute BOUNDARY_LENGTH of XC4006E_PG156 : entity is 392;

attribute BOUNDARY_REGISTER of XC4006E_PG156 : entity is
-- cellnum (type, port, function, safe[, ccell, disval, disrslt])
	"   0 (BC_1, *, internal, X)," &
	"   1 (BC_1, *, internal, X)," &
	"   2 (BC_1, *, controlr, 1)," &
	"   3 (BC_1, IO143, output3, X, 2, 1, PULL1)," &
	"   4 (BC_1, IO143, input, X)," &
	"   5 (BC_1, *, controlr, 1)," &
	"   6 (BC_1, IO144, output3, X, 5, 1, PULL1)," &
	"   7 (BC_1, IO144, input, X)," &
	"   8 (BC_1, *, controlr, 1)," &
	"   9 (BC_1, IO145, output3, X, 8, 1, PULL1)," &
	"  10 (BC_1, IO145, input, X)," &
	"  11 (BC_1, *, controlr, 1)," &
	"  12 (BC_1, IO146, output3, X, 11, 1, PULL1)," &
	"  13 (BC_1, IO146, input, X)," &
	"  14 (BC_1, *, controlr, 1)," &
	"  15 (BC_1, IO147, output3, X, 14, 1, PULL1)," &
	"  16 (BC_1, IO147, input, X)," &
	"  17 (BC_1, *, controlr, 1)," &
	"  18 (BC_1, IO148, output3, X, 17, 1, PULL1)," &
	"  19 (BC_1, IO148, input, X)," &
	"  20 (BC_1, *, controlr, 1)," &
	"  21 (BC_1, IO149, output3, X, 20, 1, PULL1)," &
	"  22 (BC_1, IO149, input, X)," &
	"  23 (BC_1, *, controlr, 1)," &
	"  24 (BC_1, IO150, output3, X, 23, 1, PULL1)," &
	"  25 (BC_1, IO150, input, X)," &
	"  26 (BC_1, *, controlr, 1)," &
	"  27 (BC_1, IO152, output3, X, 26, 1, PULL1)," &
	"  28 (BC_1, IO152, input, X)," &
	"  29 (BC_1, *, controlr, 1)," &
	"  30 (BC_1, IO153, output3, X, 29, 1, PULL1)," &
	"  31 (BC_1, IO153, input, X)," &
	"  32 (BC_1, *, controlr, 1)," &
	"  33 (BC_1, IO154, output3, X, 32, 1, PULL1)," &
	"  34 (BC_1, IO154, input, X)," &
	"  35 (BC_1, *, controlr, 1)," &
	"  36 (BC_1, IO155, output3, X, 35, 1, PULL1)," &
	"  37 (BC_1, IO155, input, X)," &
	"  38 (BC_1, *, controlr, 1)," &
	"  39 (BC_1, IO156, output3, X, 38, 1, PULL1)," &
	"  40 (BC_1, IO156, input, X)," &
	"  41 (BC_1, *, controlr, 1)," &
	"  42 (BC_1, IO157, output3, X, 41, 1, PULL1)," &
	"  43 (BC_1, IO157, input, X)," &
	"  44 (BC_1, *, controlr, 1)," &
	"  45 (BC_1, IO158, output3, X, 44, 1, PULL1)," &
	"  46 (BC_1, IO158, input, X)," &
	"  47 (BC_1, *, controlr, 1)," &
	"  48 (BC_1, IO159, output3, X, 47, 1, PULL1)," &
	"  49 (BC_1, IO159, input, X)," &
	"  50 (BC_1, *, controlr, 1)," &
	"  51 (BC_1, IO2, output3, X, 50, 1, PULL1)," &
	"  52 (BC_1, IO2, input, X)," &
	"  53 (BC_1, *, controlr, 1)," &
	"  54 (BC_1, IO3, output3, X, 53, 1, PULL1)," &
	"  55 (BC_1, IO3, input, X)," &
	"  56 (BC_1, *, controlr, 1)," &
	"  57 (BC_1, IO4, output3, X, 56, 1, PULL1)," &
	"  58 (BC_1, IO4, input, X)," &
	"  59 (BC_1, *, controlr, 1)," &
	"  60 (BC_1, IO5, output3, X, 59, 1, PULL1)," &
	"  61 (BC_1, IO5, input, X)," &
	"  62 (BC_1, *, controlr, 1)," &
	"  63 (BC_1, IO6, output3, X, 62, 1, PULL1)," &
	"  64 (BC_1, IO6, input, X)," &
	"  65 (BC_1, *, controlr, 1)," &
	"  66 (BC_1, IO7, output3, X, 65, 1, PULL1)," &
	"  67 (BC_1, IO7, input, X)," &
	"  68 (BC_1, *, controlr, 1)," &
	"  69 (BC_1, IO8, output3, X, 68, 1, PULL1)," &
	"  70 (BC_1, IO8, input, X)," &
	"  71 (BC_1, *, controlr, 1)," &
	"  72 (BC_1, IO9, output3, X, 71, 1, PULL1)," &
	"  73 (BC_1, IO9, input, X)," &
	"  74 (BC_1, *, controlr, 1)," &
	"  75 (BC_1, IO11, output3, X, 74, 1, PULL1)," &
	"  76 (BC_1, IO11, input, X)," &
	"  77 (BC_1, *, controlr, 1)," &
	"  78 (BC_1, IO12, output3, X, 77, 1, PULL1)," &
	"  79 (BC_1, IO12, input, X)," &
	"  80 (BC_1, *, controlr, 1)," &
	"  81 (BC_1, IO13, output3, X, 80, 1, PULL1)," &
	"  82 (BC_1, IO13, input, X)," &
	"  83 (BC_1, *, controlr, 1)," &
	"  84 (BC_1, IO14, output3, X, 83, 1, PULL1)," &
	"  85 (BC_1, IO14, input, X)," &
	"  86 (BC_1, *, controlr, 1)," &
	"  87 (BC_1, IO15, output3, X, 86, 1, PULL1)," &
	"  88 (BC_1, IO15, input, X)," &
	"  89 (BC_1, *, controlr, 1)," &
	"  90 (BC_1, IO16, output3, X, 89, 1, PULL1)," &
	"  91 (BC_1, IO16, input, X)," &
	"  92 (BC_1, *, controlr, 1)," &
	"  93 (BC_1, IO17, output3, X, 92, 1, PULL1)," &
	"  94 (BC_1, IO17, input, X)," &
	"  95 (BC_1, *, controlr, 1)," &
	"  96 (BC_1, IO18, output3, X, 95, 1, PULL1)," &
	"  97 (BC_1, IO18, input, X)," &
	"  98 (BC_1, *, controlr, 1)," &
	"  99 (BC_1, IO22, output3, X, 98, 1, PULL1)," &
	" 100 (BC_1, IO22, input, X)," &
	" 101 (BC_1, *, controlr, 1)," &
	" 102 (BC_1, IO23, output3, X, 101, 1, PULL1)," &
	" 103 (BC_1, IO23, input, X)," &
	" 104 (BC_1, *, controlr, 1)," &
	" 105 (BC_1, IO24, output3, X, 104, 1, PULL1)," &
	" 106 (BC_1, IO24, input, X)," &
	" 107 (BC_1, *, controlr, 1)," &
	" 108 (BC_1, IO25, output3, X, 107, 1, PULL1)," &
	" 109 (BC_1, IO25, input, X)," &
	" 110 (BC_1, *, internal, X)," &
	" 111 (BC_1, *, internal, X)," &
	" 112 (BC_1, *, internal, X)," &
	" 113 (BC_1, *, internal, X)," &
	" 114 (BC_1, *, internal, X)," &
	" 115 (BC_1, *, internal, X)," &
	" 116 (BC_1, *, controlr, 1)," &
	" 117 (BC_1, IO28, output3, X, 116, 1, PULL1)," &
	" 118 (BC_1, IO28, input, X)," &
	" 119 (BC_1, *, internal, 1)," & -- IO29.T
	" 120 (BC_1, *, internal, X)," & -- IO29.O
	" 121 (BC_1, *, internal, X)," & -- IO29.I
	" 122 (BC_1, *, controlr, 1)," &
	" 123 (BC_1, IO31, output3, X, 122, 1, PULL1)," &
	" 124 (BC_1, IO31, input, X)," &
	" 125 (BC_1, *, controlr, 1)," &
	" 126 (BC_1, IO32, output3, X, 125, 1, PULL1)," &
	" 127 (BC_1, IO32, input, X)," &
	" 128 (BC_1, *, internal, X)," &
	" 129 (BC_1, *, internal, X)," &
	" 130 (BC_1, *, internal, X)," &
	" 131 (BC_1, *, controlr, 1)," &
	" 132 (BC_1, IO34, output3, X, 131, 1, PULL1)," &
	" 133 (BC_1, IO34, input, X)," &
	" 134 (BC_1, *, controlr, 1)," &
	" 135 (BC_1, IO35, output3, X, 134, 1, PULL1)," &
	" 136 (BC_1, IO35, input, X)," &
	" 137 (BC_1, *, controlr, 1)," &
	" 138 (BC_1, IO36, output3, X, 137, 1, PULL1)," &
	" 139 (BC_1, IO36, input, X)," &
	" 140 (BC_1, *, controlr, 1)," &
	" 141 (BC_1, IO37, output3, X, 140, 1, PULL1)," &
	" 142 (BC_1, IO37, input, X)," &
	" 143 (BC_1, *, controlr, 1)," &
	" 144 (BC_1, IO38, output3, X, 143, 1, PULL1)," &
	" 145 (BC_1, IO38, input, X)," &
	" 146 (BC_1, *, controlr, 1)," &
	" 147 (BC_1, IO41, output3, X, 146, 1, PULL1)," &
	" 148 (BC_1, IO41, input, X)," &
	" 149 (BC_1, *, controlr, 1)," &
	" 150 (BC_1, IO42, output3, X, 149, 1, PULL1)," &
	" 151 (BC_1, IO42, input, X)," &
	" 152 (BC_1, *, controlr, 1)," &
	" 153 (BC_1, IO43, output3, X, 152, 1, PULL1)," &
	" 154 (BC_1, IO43, input, X)," &
	" 155 (BC_1, *, controlr, 1)," &
	" 156 (BC_1, IO44, output3, X, 155, 1, PULL1)," &
	" 157 (BC_1, IO44, input, X)," &
	" 158 (BC_1, *, controlr, 1)," &
	" 159 (BC_1, IO45, output3, X, 158, 1, PULL1)," &
	" 160 (BC_1, IO45, input, X)," &
	" 161 (BC_1, *, controlr, 1)," &
	" 162 (BC_1, IO46, output3, X, 161, 1, PULL1)," &
	" 163 (BC_1, IO46, input, X)," &
	" 164 (BC_1, *, controlr, 1)," &
	" 165 (BC_1, IO47, output3, X, 164, 1, PULL1)," &
	" 166 (BC_1, IO47, input, X)," &
	" 167 (BC_1, *, controlr, 1)," &
	" 168 (BC_1, IO48, output3, X, 167, 1, PULL1)," &
	" 169 (BC_1, IO48, input, X)," &
	" 170 (BC_1, *, controlr, 1)," &
	" 171 (BC_1, IO50, output3, X, 170, 1, PULL1)," &
	" 172 (BC_1, IO50, input, X)," &
	" 173 (BC_1, *, internal, 1)," & -- IO51.T
	" 174 (BC_1, *, internal, X)," & -- IO51.O
	" 175 (BC_1, *, internal, X)," & -- IO51.I
	" 176 (BC_1, *, controlr, 1)," &
	" 177 (BC_1, IO52, output3, X, 176, 1, PULL1)," &
	" 178 (BC_1, IO52, input, X)," &
	" 179 (BC_1, *, controlr, 1)," &
	" 180 (BC_1, IO53, output3, X, 179, 1, PULL1)," &
	" 181 (BC_1, IO53, input, X)," &
	" 182 (BC_1, *, controlr, 1)," &
	" 183 (BC_1, IO54, output3, X, 182, 1, PULL1)," &
	" 184 (BC_1, IO54, input, X)," &
	" 185 (BC_1, *, controlr, 1)," &
	" 186 (BC_1, IO55, output3, X, 185, 1, PULL1)," &
	" 187 (BC_1, IO55, input, X)," &
	" 188 (BC_1, *, controlr, 1)," &
	" 189 (BC_1, IO56, output3, X, 188, 1, PULL1)," &
	" 190 (BC_1, IO56, input, X)," &
	" 191 (BC_1, *, controlr, 1)," &
	" 192 (BC_1, IO57, output3, X, 191, 1, PULL1)," &
	" 193 (BC_1, IO57, input, X)," &
	" 194 (BC_1, *, controlr, 1)," &
	" 195 (BC_1, M1, output3, X, 194, 1, PULL1)," &
	" 196 (BC_1, M1, input, X)," &
	" 197 (BC_1, M0, input, X)," &
	" 198 (BC_1, M2, input, X)," &
	" 199 (BC_1, *, controlr, 1)," &
	" 200 (BC_1, IO63, output3, X, 199, 1, PULL1)," &
	" 201 (BC_1, IO63, input, X)," &
	" 202 (BC_1, *, controlr, 1)," &
	" 203 (BC_1, IO64, output3, X, 202, 1, PULL1)," &
	" 204 (BC_1, IO64, input, X)," &
	" 205 (BC_1, *, controlr, 1)," &
	" 206 (BC_1, IO65, output3, X, 205, 1, PULL1)," &
	" 207 (BC_1, IO65, input, X)," &
	" 208 (BC_1, *, controlr, 1)," &
	" 209 (BC_1, IO66, output3, X, 208, 1, PULL1)," &
	" 210 (BC_1, IO66, input, X)," &
	" 211 (BC_1, *, controlr, 1)," &
	" 212 (BC_1, IO67, output3, X, 211, 1, PULL1)," &
	" 213 (BC_1, IO67, input, X)," &
	" 214 (BC_1, *, controlr, 1)," &
	" 215 (BC_1, IO68, output3, X, 214, 1, PULL1)," &
	" 216 (BC_1, IO68, input, X)," &
	" 217 (BC_1, *, controlr, 1)," &
	" 218 (BC_1, IO69, output3, X, 217, 1, PULL1)," &
	" 219 (BC_1, IO69, input, X)," &
	" 220 (BC_1, *, controlr, 1)," &
	" 221 (BC_1, IO70, output3, X, 220, 1, PULL1)," &
	" 222 (BC_1, IO70, input, X)," &
	" 223 (BC_1, *, controlr, 1)," &
	" 224 (BC_1, IO72, output3, X, 223, 1, PULL1)," &
	" 225 (BC_1, IO72, input, X)," &
	" 226 (BC_1, *, controlr, 1)," &
	" 227 (BC_1, IO73, output3, X, 226, 1, PULL1)," &
	" 228 (BC_1, IO73, input, X)," &
	" 229 (BC_1, *, controlr, 1)," &
	" 230 (BC_1, IO74, output3, X, 229, 1, PULL1)," &
	" 231 (BC_1, IO74, input, X)," &
	" 232 (BC_1, *, controlr, 1)," &
	" 233 (BC_1, IO75, output3, X, 232, 1, PULL1)," &
	" 234 (BC_1, IO75, input, X)," &
	" 235 (BC_1, *, controlr, 1)," &
	" 236 (BC_1, IO76, output3, X, 235, 1, PULL1)," &
	" 237 (BC_1, IO76, input, X)," &
	" 238 (BC_1, *, controlr, 1)," &
	" 239 (BC_1, IO77, output3, X, 238, 1, PULL1)," &
	" 240 (BC_1, IO77, input, X)," &
	" 241 (BC_1, *, controlr, 1)," &
	" 242 (BC_1, IO78, output3, X, 241, 1, PULL1)," &
	" 243 (BC_1, IO78, input, X)," &
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the following line.
-- Repeat for registers 244 through 246.
-- 	" 244 (BC_1, *, controlr, 1)," &
	" 244 (BC_1, *, internal, 1)," & 
-- 	" 245 (BC_1, INIT, output3, X, 244, 1, PULL1)," &
	" 245 (BC_1, *, internal, 0)," & 
-- 	" 246 (BC_1, INIT, input, X)," &
	" 246 (BC_1, *, internal, X)," & 
	" 247 (BC_1, *, controlr, 1)," &
	" 248 (BC_1, IO82, output3, X, 247, 1, PULL1)," &
	" 249 (BC_1, IO82, input, X)," &
	" 250 (BC_1, *, controlr, 1)," &
	" 251 (BC_1, IO83, output3, X, 250, 1, PULL1)," &
	" 252 (BC_1, IO83, input, X)," &
	" 253 (BC_1, *, controlr, 1)," &
	" 254 (BC_1, IO84, output3, X, 253, 1, PULL1)," &
	" 255 (BC_1, IO84, input, X)," &
	" 256 (BC_1, *, controlr, 1)," &
	" 257 (BC_1, IO85, output3, X, 256, 1, PULL1)," &
	" 258 (BC_1, IO85, input, X)," &
	" 259 (BC_1, *, controlr, 1)," &
	" 260 (BC_1, IO86, output3, X, 259, 1, PULL1)," &
	" 261 (BC_1, IO86, input, X)," &
	" 262 (BC_1, *, controlr, 1)," &
	" 263 (BC_1, IO87, output3, X, 262, 1, PULL1)," &
	" 264 (BC_1, IO87, input, X)," &
	" 265 (BC_1, *, controlr, 1)," &
	" 266 (BC_1, IO88, output3, X, 265, 1, PULL1)," &
	" 267 (BC_1, IO88, input, X)," &
	" 268 (BC_1, *, controlr, 1)," &
	" 269 (BC_1, IO89, output3, X, 268, 1, PULL1)," &
	" 270 (BC_1, IO89, input, X)," &
	" 271 (BC_1, *, controlr, 1)," &
	" 272 (BC_1, IO91, output3, X, 271, 1, PULL1)," &
	" 273 (BC_1, IO91, input, X)," &
	" 274 (BC_1, *, controlr, 1)," &
	" 275 (BC_1, IO92, output3, X, 274, 1, PULL1)," &
	" 276 (BC_1, IO92, input, X)," &
	" 277 (BC_1, *, controlr, 1)," &
	" 278 (BC_1, IO93, output3, X, 277, 1, PULL1)," &
	" 279 (BC_1, IO93, input, X)," &
	" 280 (BC_1, *, controlr, 1)," &
	" 281 (BC_1, IO94, output3, X, 280, 1, PULL1)," &
	" 282 (BC_1, IO94, input, X)," &
	" 283 (BC_1, *, controlr, 1)," &
	" 284 (BC_1, IO95, output3, X, 283, 1, PULL1)," &
	" 285 (BC_1, IO95, input, X)," &
	" 286 (BC_1, *, controlr, 1)," &
	" 287 (BC_1, IO96, output3, X, 286, 1, PULL1)," &
	" 288 (BC_1, IO96, input, X)," &
	" 289 (BC_1, *, controlr, 1)," &
	" 290 (BC_1, IO97, output3, X, 289, 1, PULL1)," &
	" 291 (BC_1, IO97, input, X)," &
	" 292 (BC_1, *, controlr, 1)," &
	" 293 (BC_1, IO98, output3, X, 292, 1, PULL1)," &
	" 294 (BC_1, IO98, input, X)," &
	" 295 (BC_1, *, controlr, 1)," &
	" 296 (BC_1, IO103, output3, X, 295, 1, PULL1)," &
	" 297 (BC_1, IO103, input, X)," &
	" 298 (BC_1, *, controlr, 1)," &
	" 299 (BC_1, IO104, output3, X, 298, 1, PULL1)," &
	" 300 (BC_1, IO104, input, X)," &
	" 301 (BC_1, *, controlr, 1)," &
	" 302 (BC_1, IO105, output3, X, 301, 1, PULL1)," &
	" 303 (BC_1, IO105, input, X)," &
	" 304 (BC_1, *, controlr, 1)," &
	" 305 (BC_1, IO106, output3, X, 304, 1, PULL1)," &
	" 306 (BC_1, IO106, input, X)," &
	" 307 (BC_1, *, controlr, 1)," &
	" 308 (BC_1, IO107, output3, X, 307, 1, PULL1)," &
	" 309 (BC_1, IO107, input, X)," &
	" 310 (BC_1, *, controlr, 1)," &
	" 311 (BC_1, IO108, output3, X, 310, 1, PULL1)," &
	" 312 (BC_1, IO108, input, X)," &
	" 313 (BC_1, *, controlr, 1)," &
	" 314 (BC_1, IO109, output3, X, 313, 1, PULL1)," &
	" 315 (BC_1, IO109, input, X)," &
	" 316 (BC_1, *, controlr, 1)," &
	" 317 (BC_1, IO110, output3, X, 316, 1, PULL1)," &
	" 318 (BC_1, IO110, input, X)," &
	" 319 (BC_1, *, controlr, 1)," &
	" 320 (BC_1, IO112, output3, X, 319, 1, PULL1)," &
	" 321 (BC_1, IO112, input, X)," &
	" 322 (BC_1, *, controlr, 1)," &
	" 323 (BC_1, IO113, output3, X, 322, 1, PULL1)," &
	" 324 (BC_1, IO113, input, X)," &
	" 325 (BC_1, *, controlr, 1)," &
	" 326 (BC_1, IO114, output3, X, 325, 1, PULL1)," &
	" 327 (BC_1, IO114, input, X)," &
	" 328 (BC_1, *, controlr, 1)," &
	" 329 (BC_1, IO115, output3, X, 328, 1, PULL1)," &
	" 330 (BC_1, IO115, input, X)," &
	" 331 (BC_1, *, controlr, 1)," &
	" 332 (BC_1, IO116, output3, X, 331, 1, PULL1)," &
	" 333 (BC_1, IO116, input, X)," &
	" 334 (BC_1, *, controlr, 1)," &
	" 335 (BC_1, IO117, output3, X, 334, 1, PULL1)," &
	" 336 (BC_1, IO117, input, X)," &
	" 337 (BC_1, *, controlr, 1)," &
	" 338 (BC_1, IO118, output3, X, 337, 1, PULL1)," &
	" 339 (BC_1, IO118, input, X)," &
	" 340 (BC_1, *, controlr, 1)," &
	" 341 (BC_1, IO119, output3, X, 340, 1, PULL1)," &
	" 342 (BC_1, IO119, input, X)," &
	" 343 (BC_1, *, controlr, 1)," &
	" 344 (BC_1, IO122, output3, X, 343, 1, PULL1)," &
	" 345 (BC_1, IO122, input, X)," &
	" 346 (BC_1, *, controlr, 1)," &
	" 347 (BC_1, IO123, output3, X, 346, 1, PULL1)," &
	" 348 (BC_1, IO123, input, X)," &
	" 349 (BC_1, *, controlr, 1)," &
	" 350 (BC_1, IO124, output3, X, 349, 1, PULL1)," &
	" 351 (BC_1, IO124, input, X)," &
	" 352 (BC_1, *, controlr, 1)," &
	" 353 (BC_1, IO125, output3, X, 352, 1, PULL1)," &
	" 354 (BC_1, IO125, input, X)," &
	" 355 (BC_1, *, controlr, 1)," &
	" 356 (BC_1, IO126, output3, X, 355, 1, PULL1)," &
	" 357 (BC_1, IO126, input, X)," &
	" 358 (BC_1, *, controlr, 1)," &
	" 359 (BC_1, IO127, output3, X, 358, 1, PULL1)," &
	" 360 (BC_1, IO127, input, X)," &
	" 361 (BC_1, *, controlr, 1)," &
	" 362 (BC_1, IO128, output3, X, 361, 1, PULL1)," &
	" 363 (BC_1, IO128, input, X)," &
	" 364 (BC_1, *, controlr, 1)," &
	" 365 (BC_1, IO129, output3, X, 364, 1, PULL1)," &
	" 366 (BC_1, IO129, input, X)," &
	" 367 (BC_1, *, controlr, 1)," &
	" 368 (BC_1, IO131, output3, X, 367, 1, PULL1)," &
	" 369 (BC_1, IO131, input, X)," &
	" 370 (BC_1, *, internal, 1)," & -- IO132.T
	" 371 (BC_1, *, internal, X)," & -- IO132.O
	" 372 (BC_1, *, internal, X)," & -- IO132.I
	" 373 (BC_1, *, controlr, 1)," &
	" 374 (BC_1, IO133, output3, X, 373, 1, PULL1)," &
	" 375 (BC_1, IO133, input, X)," &
	" 376 (BC_1, *, controlr, 1)," &
	" 377 (BC_1, IO134, output3, X, 376, 1, PULL1)," &
	" 378 (BC_1, IO134, input, X)," &
	" 379 (BC_1, *, controlr, 1)," &
	" 380 (BC_1, IO135, output3, X, 379, 1, PULL1)," &
	" 381 (BC_1, IO135, input, X)," &
	" 382 (BC_1, *, controlr, 1)," &
	" 383 (BC_1, IO136, output3, X, 382, 1, PULL1)," &
	" 384 (BC_1, IO136, input, X)," &
	" 385 (BC_1, *, controlr, 1)," &
	" 386 (BC_1, IO137, output3, X, 385, 1, PULL1)," &
	" 387 (BC_1, IO137, input, X)," &
	" 388 (BC_1, *, controlr, 1)," &
	" 389 (BC_1, IO138, output3, X, 388, 1, PULL1)," &
	" 390 (BC_1, IO138, input, X)," &
	" 391 (BC_1, *, internal, X)";
--end boundary register

attribute DESIGN_WARNING of XC4006E_PG156 : entity is
	"CCLK and DONE are not represented in BOUNDARY_REGISTER." &
	"This BSDL file must be modified by the FPGA designer in order to" &
		"reflect post-configuration behavior (if any)." &
	"If INIT has been high or floating since power-on or the last" &
		"rising edge of PROGRAM, then the device may be in" &
		"configuration mode in which case this file is not valid." &
	"The output and tristate capture values are not valid until after" &
		"the device is configured." &
	"The tristate control is not captured properly when GTS is activated." &
	"Some pins have both controlled and uncontrolled input paths.";

end XC4006E_PG156;