------------------------------------------------------------------------
-- A T M E L A R M M I C R O C O N T R O L L E R S --
------------------------------------------------------------------------
-- BSDL file
--
-- File Name: sam3s1b_qfn64.bsdl
-- File Revision: 2.1
-- Date: Wed Jan 13 15:46:46 2010
-- Created by: Atmel Corporation
-- File Status: Released
--
-- Device: sam3s1b
-- Package: qfn64
--
-- Visit http://www.atmel.com for a updated list of BSDL files.
--
------------------------------------------------------------------------
-- Syntax and Semantics are checked against the IEEE 1149.1 standard. --
-- The logical functioning of the standard Boundary-Scan instructions --
-- and of the associated bypass, idcode and boundary-scan register --
-- described in this BSDL file has been verified against its related --
-- silicon by JTAG Technologies B.V. --
------------------------------------------------------------------------
------------------------------------------------------------------------
-- IMPORTANT NOTICE --
-- --
-- Copyright 2005 Atmel Corporation. All Rights Reserved. --
-- --
-- Atmel assumes no responsibility or liability arising out --
-- this application or use of any information described herein --
-- except as expressly agreed to in writing by Atmel Corporation. --
-- --
-- ------------------------------------------------------------------ --
-- This BSDL File has been verified on severals BSDL Syntax --
-- Checker/Compilers --
-- --
--Your job has completed. Please review the information below for the results.
--Job Status: Pass
--File Name: sam3s1b_qfn64.bsdl
--Timestamp: Sunday, February 13, 2011 8:47 PM
--Results: Entity name: SAM3S1B
--IEEE Std 1149.1-2001 (Version 2.0)
--Packaging option selected is QFN64.
--Inputs = 0
--Outputs = 0
--Bidirectionals = 38
--Instruction Reg Length = 3
--Boundary Reg Length = 142
--BSDL compilation of 487 lines completed without errors.
-- *****************************************************************************
entity sam3s1b is
-- This section identifies the default device package selected.
generic (PHYSICAL_PIN_MAP: string:= "qfn64");
-- This section declares all the ports in the design.
port (
TDI : in bit;
TMS : in bit;
TCK : in bit;
NRST : in bit;
PA0 : inout bit;
PA10 : linkage bit;
PA11 : inout bit;
PA12 : inout bit;
PA13 : inout bit;
PA14 : inout bit;
PA15 : inout bit;
PA16 : inout bit;
PA17 : inout bit;
PA18 : inout bit;
PA19 : inout bit;
PA1 : inout bit;
PA20 : inout bit;
PA21 : inout bit;
PA22 : inout bit;
PA23 : inout bit;
PA24 : inout bit;
PA25 : inout bit;
PA26 : inout bit;
PA27 : inout bit;
PA28 : inout bit;
PA29 : inout bit;
PA2 : inout bit;
PA30 : inout bit;
PA31 : inout bit;
PA3 : inout bit;
PA4 : inout bit;
PA5 : inout bit;
PA6 : inout bit;
PA9 : inout bit;
PB0 : inout bit;
PB1 : inout bit;
PB10 : inout bit;
PB11 : inout bit;
PB12 : inout bit;
PB13 : inout bit;
PB14 : inout bit;
PB2 : inout bit;
PB3 : inout bit;
TDO : out bit;
JTAGSEL : in bit;
PA7 : linkage bit;
PA8 : linkage bit;
PB8 : linkage bit;
PB9 : linkage bit;
TST : in bit
);
use STD_1149_1_2001.all;
attribute COMPONENT_CONFORMANCE of sam3s1b : entity is "STD_1149_1_2001";
attribute PIN_MAP of sam3s1b: entity is PHYSICAL_PIN_MAP;
-- This section specifies the pin map for each port. This information is
-- extracted from the port-to-pin map file that was read in using the
-- "read_pin_map" command.
constant qfn64: PIN_MAP_STRING :=
"TDI : 33," &
"TMS : 51," &
"TCK : 53," &
"NRST : 39," &
"PA0 : 48," &
"PA10 : 29," &
"PA11 : 28," &
"PA12 : 27," &
"PA13 : 22," &
"PA14 : 21," &
"PA15 : 20," &
"PA16 : 19," &
"PA17 : 9," &
"PA18 : 10," &
"PA19 : 13," &
"PA1 : 47," &
"PA20 : 11," &
"PA21 : 16," &
"PA22 : 14," &
"PA23 : 15," &
"PA24 : 23," &
"PA25 : 25," &
"PA26 : 26," &
"PA27 : 37," &
"PA28 : 38," &
"PA29 : 41," &
"PA2 : 44," &
"PA30 : 42," &
"PA31 : 52," &
"PA3 : 43," &
"PA4 : 36," &
"PA5 : 35," &
"PA6 : 34," &
"PA9 : 30," &
"PB0 : 3," &
"PB1 : 4," &
"PB10 : 56," &
"PB11 : 57," &
"PB12 : 55," &
"PB13 : 59," &
"PB14 : 63," &
"PB2 : 5," &
"PB3 : 6," &
"TDO : 49," &
"JTAGSEL : 50," &
"PA7 : 32," &
"PA8 : 31," &
"PB8 : 61," &
"PB9 : 62," &
"TST : 40";
-- This section specifies the TAP ports. For the TAP TCK port, the parameters in
-- the brackets are:
-- First Field : Maximum TCK frequency.
-- Second Field: Allowable states TCK may be stopped in.
attribute TAP_SCAN_CLOCK of TCK : signal is (1.000000e+06, BOTH);
attribute TAP_SCAN_IN of TDI : signal is true;
attribute TAP_SCAN_MODE of TMS : signal is true;
attribute TAP_SCAN_OUT of TDO : signal is true;
attribute TAP_SCAN_RESET of NRST: signal is true;
-- Specifies the compliance enable patterns for the design. It lists a set of
-- design ports and the values that they should be set to, in order to enable
-- compliance to IEEE Std 1149.1
attribute COMPLIANCE_PATTERNS of sam3s1b: entity is
"(JTAGSEL, TST) (10)";
-- Specifies the number of bits in the instruction register.
attribute INSTRUCTION_LENGTH of sam3s1b: entity is 3;
-- Specifies the boundary-scan instructions implemented in the design and their
-- opcodes.
attribute INSTRUCTION_OPCODE of sam3s1b: entity is
"BYPASS (111, 101, 110)," &
"EXTEST (000)," &
"SAMPLE (100)," &
"PRELOAD (100)," &
"USER1 (010)," &
"HIGHZ (001)," &
"IDCODE (011)";
-- Specifies the bit pattern that is loaded into the instruction register when
-- the TAP controller passes through the Capture-IR state. The standard mandates
-- that the two LSBs must be "01". The remaining bits are design specific.
attribute INSTRUCTION_CAPTURE of sam3s1b: entity is "001";
-- Specifies the bit pattern that is loaded into the DEVICE_ID register during
-- the IDCODE instruction when the TAP controller passes through the Capture-DR
-- state.
attribute IDCODE_REGISTER of sam3s1b: entity is
"0000" &
-- 4-bit version number
"0101101100101101" &
-- 16-bit part number
"00000011111" &
-- 11-bit identity of the manufacturer
"1";
-- Required by IEEE Std 1149.1
-- This section specifies the TST data register placed between TDI and TDO for
-- each implemented instruction.
attribute REGISTER_ACCESS of sam3s1b: entity is
"BYPASS (BYPASS, HIGHZ)," &
"BOUNDARY (EXTEST, SAMPLE, USER1)," &
"DEVICE_ID (IDCODE)";
-- Specifies the length of the boundary scan register.
attribute BOUNDARY_LENGTH of sam3s1b: entity is 142;
-- The following list specifies the characteristics of each cell in the boundary
-- scan register from TDI to TDO. The following is a description of the label
-- fields:
-- num : Is the cell number.
-- cell : Is the cell type as defined by the standard.
-- port : Is the design port name. Control cells do not have a port
-- name.
-- function: Is the function of the cell as defined by the standard. Is one
-- of input, output2, output3, bidir, control or controlr.
-- safe : Specifies the value that the BSR cell should be loaded with
-- for safe operation when the software might otherwise choose a
-- random value.
-- ccell : The control cell number. Specifies the control cell that
-- drives the output enable for this port.
-- disval : Specifies the value that is loaded into the control cell to
-- disable the output enable for the corresponding port.
-- rslt : Resulting state. Shows the state of the driver when it is
-- disabled.
attribute BOUNDARY_REGISTER of sam3s1b: entity is
--
-- num cell port function safe [ccell disval
-- rslt]
--
"141 (BC_1, *, control, " &
"1), " &
"140 (BC_7, PA16, bidir, X, 141, " &
"1, Z), " &
"139 (BC_0, *, internal, X), " &
"138 (BC_0, *, internal, X), " &
"137 (BC_1, *, control, " &
"1), " &
"136 (BC_7, PA15, bidir, X, 137, " &
"1, Z), " &
"135 (BC_1, *, control, " &
"1), " &
"134 (BC_7, PA14, bidir, X, 135, " &
"1, Z), " &
"133 (BC_0, *, internal, X), " &
"132 (BC_0, *, internal, X), " &
"131 (BC_1, *, control, " &
"1), " &
"130 (BC_7, PA13, bidir, X, 131, " &
"1, Z), " &
"129 (BC_1, *, control, " &
"1), " &
"128 (BC_7, PA24, bidir, X, 129, " &
"1, Z), " &
"127 (BC_0, *, internal, X), " &
"126 (BC_0, *, internal, X), " &
"125 (BC_0, *, internal, X), " &
"124 (BC_0, *, internal, X), " &
"123 (BC_1, *, control, " &
"1), " &
"122 (BC_7, PA25, bidir, X, 123, " &
"1, Z), " &
"121 (BC_1, *, control, " &
"1), " &
"120 (BC_7, PA26, bidir, X, 121, " &
"1, Z), " &
"119 (BC_0, *, internal, X), " &
"118 (BC_0, *, internal, X), " &
"117 (BC_1, *, control, " &
"1), " &
"116 (BC_7, PA12, bidir, X, 117, " &
"1, Z), " &
"115 (BC_1, *, control, " &
"1), " &
"114 (BC_7, PA11, bidir, X, 115, " &
"1, Z), " &
"113 (BC_0, *, internal, X), " &
"112 (BC_0, *, internal, X), " &
"111 (BC_0, *, internal, X), " &
"110 (BC_0, *, internal, X), " &
"109 (BC_1, *, control, " &
"1), " &
"108 (BC_7, PA9, bidir, X, 109, " &
"1, Z), " &
"107 (BC_0, *, internal, X), " &
"106 (BC_0, *, internal, X), " &
"105 (BC_1, *, control, " &
"1), " &
"104 (BC_7, PA6, bidir, X, 105, " &
"1, Z), " &
"103 (BC_1, *, control, " &
"1), " &
"102 (BC_7, PA5, bidir, X, 103, " &
"1, Z), " &
"101 (BC_0, *, internal, X), " &
"100 (BC_0, *, internal, X), " &
"99 (BC_1, *, control, " &
"1), " &
"98 (BC_7, PA4, bidir, X, 99, " &
"1, Z), " &
"97 (BC_1, *, control, " &
"1), " &
"96 (BC_7, PA27, bidir, X, 97, " &
"1, Z), " &
"95 (BC_0, *, internal, X), " &
"94 (BC_0, *, internal, X), " &
"93 (BC_1, *, control, " &
"1), " &
"92 (BC_7, PA28, bidir, X, 93, " &
"1, Z), " &
"91 (BC_0, *, internal, X), " &
"90 (BC_0, *, internal, X), " &
"89 (BC_1, *, control, " &
"1), " &
"88 (BC_7, PA29, bidir, X, 89, " &
"1, Z), " &
"87 (BC_1, *, control, " &
"1), " &
"86 (BC_7, PA30, bidir, X, 87, " &
"1, Z), " &
"85 (BC_0, *, internal, X), " &
"84 (BC_0, *, internal, X), " &
"83 (BC_1, *, control, " &
"1), " &
"82 (BC_7, PA3, bidir, X, 83, " &
"1, Z), " &
"81 (BC_1, *, control, " &
"1), " &
"80 (BC_7, PA2, bidir, X, 81, " &
"1, Z), " &
"79 (BC_0, *, internal, X), " &
"78 (BC_0, *, internal, X), " &
"77 (BC_0, *, internal, X), " &
"76 (BC_0, *, internal, X), " &
"75 (BC_1, *, control, " &
"1), " &
"74 (BC_7, PA1, bidir, X, 75, " &
"1, Z), " &
"73 (BC_0, *, internal, X), " &
"72 (BC_0, *, internal, X), " &
"71 (BC_1, *, control, " &
"1), " &
"70 (BC_7, PA0, bidir, X, 71, " &
"1, Z), " &
"69 (BC_0, *, internal, X), " &
"68 (BC_0, *, internal, X), " &
"67 (BC_0, *, internal, X), " &
"66 (BC_0, *, internal, X), " &
"65 (BC_0, *, internal, X), " &
"64 (BC_0, *, internal, X), " &
"63 (BC_1, *, control, " &
"1), " &
"62 (BC_7, PA31, bidir, X, 63, " &
"1, Z), " &
"61 (BC_0, *, internal, X), " &
"60 (BC_0, *, internal, X), " &
"59 (BC_0, *, internal, X), " &
"58 (BC_0, *, internal, X), " &
"57 (BC_0, *, internal, X), " &
"56 (BC_0, *, internal, X), " &
"55 (BC_1, *, control, " &
"1), " &
"54 (BC_7, PB12, bidir, X, 55, " &
"1, Z), " &
"53 (BC_1, *, control, " &
"1), " &
"52 (BC_7, PB10, bidir, X, 53, " &
"1, Z), " &
"51 (BC_1, *, control, " &
"1), " &
"50 (BC_7, PB11, bidir, X, 51, " &
"1, Z), " &
"49 (BC_0, *, internal, X), " &
"48 (BC_0, *, internal, X), " &
"47 (BC_0, *, internal, X), " &
"46 (BC_0, *, internal, X), " &
"45 (BC_1, *, control, " &
"1), " &
"44 (BC_7, PB13, bidir, X, 45, " &
"1, Z), " &
"43 (BC_0, *, internal, X), " &
"42 (BC_0, *, internal, X), " &
"41 (BC_1, *, control, " &
"1), " &
"40 (BC_7, PB14, bidir, X, 41, " &
"1, Z), " &
"39 (BC_1, *, control, " &
"1), " &
"38 (BC_7, PB0, bidir, X, 39, " &
"1, Z), " &
"37 (BC_0, *, internal, X), " &
"36 (BC_0, *, internal, X), " &
"35 (BC_1, *, control, " &
"1), " &
"34 (BC_7, PB1, bidir, X, 35, " &
"1, Z), " &
"33 (BC_0, *, internal, X), " &
"32 (BC_0, *, internal, X), " &
"31 (BC_1, *, control, " &
"1), " &
"30 (BC_7, PB2, bidir, X, 31, " &
"1, Z), " &
"29 (BC_0, *, internal, X), " &
"28 (BC_0, *, internal, X), " &
"27 (BC_1, *, control, " &
"1), " &
"26 (BC_7, PB3, bidir, X, 27, " &
"1, Z), " &
"25 (BC_1, *, control, " &
"1), " &
"24 (BC_7, PA17, bidir, X, 25, " &
"1, Z), " &
"23 (BC_0, *, internal, X), " &
"22 (BC_0, *, internal, X), " &
"21 (BC_1, *, control, " &
"1), " &
"20 (BC_7, PA18, bidir, X, 21, " &
"1, Z), " &
"19 (BC_1, *, control, " &
"1), " &
"18 (BC_7, PA21, bidir, X, 19, " &
"1, Z), " &
"17 (BC_0, *, internal, X), " &
"16 (BC_0, *, internal, X), " &
"15 (BC_1, *, control, " &
"1), " &
"14 (BC_7, PA19, bidir, X, 15, " &
"1, Z), " &
"13 (BC_0, *, internal, X), " &
"12 (BC_0, *, internal, X), " &
"11 (BC_1, *, control, " &
"1), " &
"10 (BC_7, PA22, bidir, X, 11, " &
"1, Z), " &
"9 (BC_0, *, internal, X), " &
"8 (BC_0, *, internal, X), " &
"7 (BC_1, *, control, " &
"1), " &
"6 (BC_7, PA23, bidir, X, 7, " &
"1, Z), " &
"5 (BC_0, *, internal, X), " &
"4 (BC_0, *, internal, X), " &
"3 (BC_1, *, control, " &
"1), " &
"2 (BC_7, PA20, bidir, X, 3, " &
"1, Z), " &
"1 (BC_0, *, internal, X), " &
"0 (BC_0, *, internal, X) " ;
end sam3s1b;