--$ XILINX$RCSfile: xc5204_pc84.bsd,v $
--$ XILINX$Revision: 1.3 $
--
-- BSDL file for device XC5204, package PC84
-- Xilinx, Inc. $State: FINAL $ $Date: 1997-11-12 21:35:46+00 $
-- Generated by createBSDL 2.6
--
-- For technical support, contact Xilinx as follows:
-- North America 1-800-255-7778 hotline@xilinx.com
-- United Kingdom (44) 1932 820821 ukhelp@xilinx.com
-- France (33) 1 3463 0100 frhelp@xilinx.com
-- Germany (49) 89 991 54930 dlhelp@xilinx.com
-- Japan (81) 3-3297-9163 jhotline@xilinx.com
--
-- BSDL verified to conform to 1149.1b-1994 syntax. This device has been
-- tested by the Intellitech 1149.1 Verification Lab using the Intellitech
-- Eclipse(TM) Scan Diagnostic Tool and the Intellitech RCT(TM). This
-- device has been verified to operate according to the BSDL provided,
-- and is compatible with the IEEE 1149.1 standard when the operating
-- instructions in the BSDL are followed.
-- PH: 603-868-7116 or email: scansupport@intellitech.com
--
-- This BSDL file reflects the pre-configuration JTAG behavior. To reflect
-- the post-configuration JTAG behavior (if any), edit this file as described
-- below. Many of these changes are demonstrated by commented-out template
-- lines preceeding the lines they would replace:
--
-- 1. Enable USER instructions as appropriate (see below).
-- 2. For inputs using uncontrolled paths (e.g. PGCK), change
-- boundary cell function from 'input' to 'clock' or 'observe_only'.
-- 3. Set disable result of all pads as configured.
-- 4. Set safe state of boundary cells as necessary.
-- 5. Set safe state of INIT output to X, or as necessary (see below).
-- 6. Rename entity if necessary to avoid name collisions.
-- 7. Change INIT port direction from "in" to "inout" (see below).
-- 8. Change COMPLIANCE_PATTERNS to "(PROGRAM) (1)" (see below).
-- 9. Change INIT boundary cells from internal to controlr, output3,
-- and input, respectively (see below).
-- 10. Remove the design warning regarding keeping INIT low.
--
-- NOTE: Post-configuration JTAG is available only if the BSCAN symbol
-- is instantiated in the FPGA design.
-- NOTE: PULLUP symbols must be instantiated on the TMS and TDI pins
-- in the FPGA design to comply with IEEE Std. 1149.1-1993.
entity XC5204_PC84 is
generic (PHYSICAL_PIN_MAP : string := "PC84" );
port (
CCLK: linkage bit;
DONE: linkage bit;
GND: linkage bit_vector (1 to 8);
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the following line so
-- that INIT is of type inout.
-- INIT: inout bit;
INIT: in bit;
IO3: inout bit;
IO4: inout bit;
IO7: inout bit;
IO8: inout bit;
IO13: inout bit;
IO14: inout bit;
IO17: inout bit;
IO18: inout bit;
IO21: inout bit;
IO22: inout bit;
IO30: inout bit;
IO33: inout bit;
IO34: inout bit;
IO37: inout bit;
IO38: inout bit;
IO41: inout bit;
IO42: inout bit;
IO45: inout bit;
IO49: inout bit;
IO50: inout bit;
IO56: inout bit;
IO57: inout bit;
IO61: inout bit;
IO66: inout bit;
IO67: inout bit;
IO70: inout bit;
IO74: inout bit;
IO75: inout bit;
IO78: inout bit;
IO79: inout bit;
IO84: inout bit;
IO85: inout bit;
IO88: inout bit;
IO89: inout bit;
IO94: inout bit;
IO95: inout bit;
IO98: inout bit;
IO102: inout bit;
IO103: inout bit;
IO106: inout bit;
IO107: inout bit;
IO110: inout bit;
IO111: inout bit;
IO114: inout bit;
IO115: inout bit;
IO118: inout bit;
IO119: inout bit;
IO122: inout bit;
IO123: inout bit;
IO128: inout bit;
IO129: inout bit;
IO132: inout bit;
IO133: inout bit;
IO138: inout bit;
IO139: inout bit;
IO142: inout bit;
IO143: inout bit;
M0: inout bit;
M1: inout bit;
M2: inout bit;
PROGRAM: in bit;
TCK: in bit;
TDI: in bit;
TDO: out bit;
TMS: in bit;
VDD: linkage bit_vector (1 to 8)
); --end port list
use STD_1149_1_1994.all;
attribute COMPONENT_CONFORMANCE of XC5204_PC84 : entity is
"STD_1149_1_1993";
attribute PIN_MAP of XC5204_PC84 : entity is PHYSICAL_PIN_MAP;
constant PC84: PIN_MAP_STRING:=
"CCLK:73," &
"DONE:53," &
"GND:(1,12,21,31,43,52,64,76)," &
"INIT:41," &
"IO3:3," &
"IO4:4," &
"IO7:5," &
"IO8:6," &
"IO13:7," &
"IO14:8," &
"IO17:9," &
"IO18:10," &
"IO21:13," &
"IO22:14," &
"IO30:18," &
"IO33:19," &
"IO34:20," &
"IO37:23," &
"IO38:24," &
"IO41:25," &
"IO42:26," &
"IO45:27," &
"IO49:28," &
"IO50:29," &
"IO56:35," &
"IO57:36," &
"IO61:37," &
"IO66:38," &
"IO67:39," &
"IO70:40," &
"IO74:44," &
"IO75:45," &
"IO78:46," &
"IO79:47," &
"IO84:48," &
"IO85:49," &
"IO88:50," &
"IO89:51," &
"IO94:56," &
"IO95:57," &
"IO98:58," &
"IO102:59," &
"IO103:60," &
"IO106:61," &
"IO107:62," &
"IO110:65," &
"IO111:66," &
"IO114:67," &
"IO115:68," &
"IO118:69," &
"IO119:70," &
"IO122:71," &
"IO123:72," &
"IO128:77," &
"IO129:78," &
"IO132:79," &
"IO133:80," &
"IO138:81," &
"IO139:82," &
"IO142:83," &
"IO143:84," &
"M0:32," &
"M1:30," &
"M2:34," &
"PROGRAM:55," &
"TCK:16," &
"TDI:15," &
"TDO:75," &
"TMS:17," &
"VDD:(2,11,22,33,42,54,63,74)";
--end pin map
attribute TAP_SCAN_IN of TDI : signal is true;
attribute TAP_SCAN_MODE of TMS : signal is true;
attribute TAP_SCAN_OUT of TDO : signal is true;
attribute TAP_SCAN_CLOCK of TCK : signal is (2.0e6, LOW);
-- This is conservative. Real max is expected to be (~5MHz, BOTH).
attribute COMPLIANCE_PATTERNS of XC5204_PC84 : entity is
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the corresponding line
-- below.
-- "(PROGRAM) (1)";
--
-- NOTE: If INIT has been high or floating since the later of power-on
-- and the last rising transition of PROGRAM, then the device may
-- be in configuration mode in which case some JTAG instructions
-- will not be available.
"(INIT,PROGRAM) (01)";
attribute INSTRUCTION_LENGTH of XC5204_PC84 : entity is 3;
attribute INSTRUCTION_OPCODE of XC5204_PC84 : entity is
"RESERVED (110)," &
"READBACK (100)," & -- Not available during configuration
"CONFIGURE (101)," & -- Not available during configuration
"USER2 (011)," & -- Not available until after configuration
"USER1 (010)," & -- Not available until after configuration
"SAMPLE (001)," & -- Internal capture not valid until after config
"EXTEST (000)," & -- Not available during configuration
"BYPASS (111)";
attribute INSTRUCTION_CAPTURE of XC5204_PC84 : entity is "X01";
-- MSB of instruction capture is low during configuration.
-- If the device is configured, and a USER instruction is implemented
-- and not private to the FPGA designer, then it should be removed
-- from INSTRUCTION_PRIVATE, and the target register should be defined
-- in REGISTER_ACCESS.
attribute INSTRUCTION_PRIVATE of XC5204_PC84 : entity is
"USER1," &
"USER2," &
"READBACK," &
"RESERVED," &
"CONFIGURE";
attribute REGISTER_ACCESS of XC5204_PC84 : entity is
-- "<reg_name>[<length>] (USER1)," &
-- "<reg_name>[<length>] (USER2)," &
"BYPASS (BYPASS)," &
"BOUNDARY (SAMPLE,EXTEST)";
attribute BOUNDARY_LENGTH of XC5204_PC84 : entity is 529;
attribute BOUNDARY_REGISTER of XC5204_PC84 : entity is
-- cellnum (type, port, function, safe[, ccell, disval, disrslt])
" 0 (BC_1, *, internal, X)," &
" 1 (BC_1, *, internal, X)," &
" 2 (BC_1, *, internal, X)," &
" 3 (BC_1, *, internal, X)," &
" 4 (BC_1, *, internal, X)," &
" 5 (BC_1, *, internal, X)," &
" 6 (BC_1, *, internal, X)," &
" 7 (BC_1, *, internal, X)," &
" 8 (BC_1, *, internal, X)," &
" 9 (BC_1, *, controlr, 1)," &
" 10 (BC_1, IO128, output3, X, 9, 1, PULL1)," &
" 11 (BC_1, IO128, input, X)," &
" 12 (BC_1, *, internal, X)," &
" 13 (BC_1, *, internal, X)," &
" 14 (BC_1, *, internal, X)," &
" 15 (BC_1, *, controlr, 1)," &
" 16 (BC_1, IO129, output3, X, 15, 1, PULL1)," &
" 17 (BC_1, IO129, input, X)," &
" 18 (BC_1, *, internal, 1)," & -- IO130.T
" 19 (BC_1, *, internal, X)," & -- IO130.O
" 20 (BC_1, *, internal, X)," & -- IO130.I
" 21 (BC_1, *, internal, 1)," & -- IO131.T
" 22 (BC_1, *, internal, X)," & -- IO131.O
" 23 (BC_1, *, internal, X)," & -- IO131.I
" 24 (BC_1, *, internal, X)," &
" 25 (BC_1, *, internal, X)," &
" 26 (BC_1, *, internal, X)," &
" 27 (BC_1, *, controlr, 1)," &
" 28 (BC_1, IO132, output3, X, 27, 1, PULL1)," &
" 29 (BC_1, IO132, input, X)," &
" 30 (BC_1, *, controlr, 1)," &
" 31 (BC_1, IO133, output3, X, 30, 1, PULL1)," &
" 32 (BC_1, IO133, input, X)," &
" 33 (BC_1, *, internal, 1)," & -- IO134.T
" 34 (BC_1, *, internal, X)," & -- IO134.O
" 35 (BC_1, *, internal, X)," & -- IO134.I
" 36 (BC_1, *, internal, X)," &
" 37 (BC_1, *, internal, X)," &
" 38 (BC_1, *, internal, X)," &
" 39 (BC_1, *, internal, 1)," & -- IO135.T
" 40 (BC_1, *, internal, X)," & -- IO135.O
" 41 (BC_1, *, internal, X)," & -- IO135.I
" 42 (BC_1, *, internal, 1)," & -- IO136.T
" 43 (BC_1, *, internal, X)," & -- IO136.O
" 44 (BC_1, *, internal, X)," & -- IO136.I
" 45 (BC_1, *, internal, 1)," & -- IO137.T
" 46 (BC_1, *, internal, X)," & -- IO137.O
" 47 (BC_1, *, internal, X)," & -- IO137.I
" 48 (BC_1, *, internal, X)," &
" 49 (BC_1, *, internal, X)," &
" 50 (BC_1, *, internal, X)," &
" 51 (BC_1, *, controlr, 1)," &
" 52 (BC_1, IO138, output3, X, 51, 1, PULL1)," &
" 53 (BC_1, IO138, input, X)," &
" 54 (BC_1, *, controlr, 1)," &
" 55 (BC_1, IO139, output3, X, 54, 1, PULL1)," &
" 56 (BC_1, IO139, input, X)," &
" 57 (BC_1, *, internal, 1)," & -- IO140.T
" 58 (BC_1, *, internal, X)," & -- IO140.O
" 59 (BC_1, *, internal, X)," & -- IO140.I
" 60 (BC_1, *, internal, X)," &
" 61 (BC_1, *, internal, X)," &
" 62 (BC_1, *, internal, X)," &
" 63 (BC_1, *, internal, 1)," & -- IO141.T
" 64 (BC_1, *, internal, X)," & -- IO141.O
" 65 (BC_1, *, internal, X)," & -- IO141.I
" 66 (BC_1, *, controlr, 1)," &
" 67 (BC_1, IO142, output3, X, 66, 1, PULL1)," &
" 68 (BC_1, IO142, input, X)," &
" 69 (BC_1, *, controlr, 1)," &
" 70 (BC_1, IO143, output3, X, 69, 1, PULL1)," &
" 71 (BC_1, IO143, input, X)," &
" 72 (BC_1, *, internal, X)," &
" 73 (BC_1, *, internal, X)," &
" 74 (BC_1, *, internal, X)," &
" 75 (BC_1, *, internal, X)," &
" 76 (BC_1, *, internal, X)," &
" 77 (BC_1, *, internal, X)," &
" 78 (BC_1, *, controlr, 1)," &
" 79 (BC_1, IO3, output3, X, 78, 1, PULL1)," &
" 80 (BC_1, IO3, input, X)," &
" 81 (BC_1, *, controlr, 1)," &
" 82 (BC_1, IO4, output3, X, 81, 1, PULL1)," &
" 83 (BC_1, IO4, input, X)," &
" 84 (BC_1, *, internal, X)," &
" 85 (BC_1, *, internal, X)," &
" 86 (BC_1, *, internal, X)," &
" 87 (BC_1, *, internal, 1)," & -- IO5.T
" 88 (BC_1, *, internal, X)," & -- IO5.O
" 89 (BC_1, *, internal, X)," & -- IO5.I
" 90 (BC_1, *, internal, 1)," & -- IO6.T
" 91 (BC_1, *, internal, X)," & -- IO6.O
" 92 (BC_1, *, internal, X)," & -- IO6.I
" 93 (BC_1, *, controlr, 1)," &
" 94 (BC_1, IO7, output3, X, 93, 1, PULL1)," &
" 95 (BC_1, IO7, input, X)," &
" 96 (BC_1, *, internal, X)," &
" 97 (BC_1, *, internal, X)," &
" 98 (BC_1, *, internal, X)," &
" 99 (BC_1, *, controlr, 1)," &
" 100 (BC_1, IO8, output3, X, 99, 1, PULL1)," &
" 101 (BC_1, IO8, input, X)," &
" 102 (BC_1, *, internal, 1)," & -- IO9.T
" 103 (BC_1, *, internal, X)," & -- IO9.O
" 104 (BC_1, *, internal, X)," & -- IO9.I
" 105 (BC_1, *, internal, 1)," & -- IO10.T
" 106 (BC_1, *, internal, X)," & -- IO10.O
" 107 (BC_1, *, internal, X)," & -- IO10.I
" 108 (BC_1, *, internal, X)," &
" 109 (BC_1, *, internal, X)," &
" 110 (BC_1, *, internal, X)," &
" 111 (BC_1, *, internal, 1)," & -- IO11.T
" 112 (BC_1, *, internal, X)," & -- IO11.O
" 113 (BC_1, *, internal, X)," & -- IO11.I
" 114 (BC_1, *, internal, 1)," & -- IO12.T
" 115 (BC_1, *, internal, X)," & -- IO12.O
" 116 (BC_1, *, internal, X)," & -- IO12.I
" 117 (BC_1, *, controlr, 1)," &
" 118 (BC_1, IO13, output3, X, 117, 1, PULL1)," &
" 119 (BC_1, IO13, input, X)," &
" 120 (BC_1, *, internal, X)," &
" 121 (BC_1, *, internal, X)," &
" 122 (BC_1, *, internal, X)," &
" 123 (BC_1, *, controlr, 1)," &
" 124 (BC_1, IO14, output3, X, 123, 1, PULL1)," &
" 125 (BC_1, IO14, input, X)," &
" 126 (BC_1, *, internal, 1)," & -- IO15.T
" 127 (BC_1, *, internal, X)," & -- IO15.O
" 128 (BC_1, *, internal, X)," & -- IO15.I
" 129 (BC_1, *, internal, 1)," & -- IO16.T
" 130 (BC_1, *, internal, X)," & -- IO16.O
" 131 (BC_1, *, internal, X)," & -- IO16.I
" 132 (BC_1, *, internal, X)," &
" 133 (BC_1, *, internal, X)," &
" 134 (BC_1, *, internal, X)," &
" 135 (BC_1, *, internal, X)," &
" 136 (BC_1, *, internal, X)," &
" 137 (BC_1, *, internal, X)," &
" 138 (BC_1, *, controlr, 1)," &
" 139 (BC_1, IO17, output3, X, 138, 1, PULL1)," &
" 140 (BC_1, IO17, input, X)," &
" 141 (BC_1, *, controlr, 1)," &
" 142 (BC_1, IO18, output3, X, 141, 1, PULL1)," &
" 143 (BC_1, IO18, input, X)," &
" 144 (BC_1, *, internal, X)," &
" 145 (BC_1, *, internal, X)," &
" 146 (BC_1, *, internal, X)," &
" 147 (BC_1, *, internal, X)," &
" 148 (BC_1, *, internal, X)," &
" 149 (BC_1, *, internal, X)," &
" 150 (BC_1, *, controlr, 1)," &
" 151 (BC_1, IO21, output3, X, 150, 1, PULL1)," &
" 152 (BC_1, IO21, input, X)," &
" 153 (BC_1, *, controlr, 1)," &
" 154 (BC_1, IO22, output3, X, 153, 1, PULL1)," &
" 155 (BC_1, IO22, input, X)," &
" 156 (BC_1, *, internal, X)," &
" 157 (BC_1, *, internal, X)," &
" 158 (BC_1, *, internal, X)," &
" 159 (BC_1, *, internal, 1)," & -- IO23.T
" 160 (BC_1, *, internal, X)," & -- IO23.O
" 161 (BC_1, *, internal, X)," & -- IO23.I
" 162 (BC_1, *, internal, 1)," & -- IO24.T
" 163 (BC_1, *, internal, X)," & -- IO24.O
" 164 (BC_1, *, internal, X)," & -- IO24.I
" 165 (BC_1, *, internal, X)," &
" 166 (BC_1, *, internal, X)," &
" 167 (BC_1, *, internal, X)," &
" 168 (BC_1, *, internal, X)," &
" 169 (BC_1, *, internal, X)," &
" 170 (BC_1, *, internal, X)," &
" 171 (BC_1, *, internal, X)," &
" 172 (BC_1, *, internal, X)," &
" 173 (BC_1, *, internal, X)," &
" 174 (BC_1, *, internal, 1)," & -- IO27.T
" 175 (BC_1, *, internal, X)," & -- IO27.O
" 176 (BC_1, *, internal, X)," & -- IO27.I
" 177 (BC_1, *, internal, 1)," & -- IO28.T
" 178 (BC_1, *, internal, X)," & -- IO28.O
" 179 (BC_1, *, internal, X)," & -- IO28.I
" 180 (BC_1, *, internal, X)," &
" 181 (BC_1, *, internal, X)," &
" 182 (BC_1, *, internal, X)," &
" 183 (BC_1, *, controlr, 1)," &
" 184 (BC_1, IO30, output3, X, 183, 1, PULL1)," &
" 185 (BC_1, IO30, input, X)," &
" 186 (BC_1, *, internal, 1)," & -- IO31.T
" 187 (BC_1, *, internal, X)," & -- IO31.O
" 188 (BC_1, *, internal, X)," & -- IO31.I
" 189 (BC_1, *, internal, 1)," & -- IO32.T
" 190 (BC_1, *, internal, X)," & -- IO32.O
" 191 (BC_1, *, internal, X)," & -- IO32.I
" 192 (BC_1, *, internal, X)," &
" 193 (BC_1, *, internal, X)," &
" 194 (BC_1, *, internal, X)," &
" 195 (BC_1, *, controlr, 1)," &
" 196 (BC_1, IO33, output3, X, 195, 1, PULL1)," &
" 197 (BC_1, IO33, input, X)," &
" 198 (BC_1, *, controlr, 1)," &
" 199 (BC_1, IO34, output3, X, 198, 1, PULL1)," &
" 200 (BC_1, IO34, input, X)," &
" 201 (BC_1, *, controlr, 1)," &
" 202 (BC_1, IO37, output3, X, 201, 1, PULL1)," &
" 203 (BC_1, IO37, input, X)," &
" 204 (BC_1, *, internal, X)," &
" 205 (BC_1, *, internal, X)," &
" 206 (BC_1, *, internal, X)," &
" 207 (BC_1, *, controlr, 1)," &
" 208 (BC_1, IO38, output3, X, 207, 1, PULL1)," &
" 209 (BC_1, IO38, input, X)," &
" 210 (BC_1, *, internal, 1)," & -- IO39.T
" 211 (BC_1, *, internal, X)," & -- IO39.O
" 212 (BC_1, *, internal, X)," & -- IO39.I
" 213 (BC_1, *, internal, 1)," & -- IO40.T
" 214 (BC_1, *, internal, X)," & -- IO40.O
" 215 (BC_1, *, internal, X)," & -- IO40.I
" 216 (BC_1, *, internal, X)," &
" 217 (BC_1, *, internal, X)," &
" 218 (BC_1, *, internal, X)," &
" 219 (BC_1, *, controlr, 1)," &
" 220 (BC_1, IO41, output3, X, 219, 1, PULL1)," &
" 221 (BC_1, IO41, input, X)," &
" 222 (BC_1, *, controlr, 1)," &
" 223 (BC_1, IO42, output3, X, 222, 1, PULL1)," &
" 224 (BC_1, IO42, input, X)," &
" 225 (BC_1, *, internal, 1)," & -- IO43.T
" 226 (BC_1, *, internal, X)," & -- IO43.O
" 227 (BC_1, *, internal, X)," & -- IO43.I
" 228 (BC_1, *, internal, X)," &
" 229 (BC_1, *, internal, X)," &
" 230 (BC_1, *, internal, X)," &
" 231 (BC_1, *, internal, 1)," & -- IO44.T
" 232 (BC_1, *, internal, X)," & -- IO44.O
" 233 (BC_1, *, internal, X)," & -- IO44.I
" 234 (BC_1, *, controlr, 1)," &
" 235 (BC_1, IO45, output3, X, 234, 1, PULL1)," &
" 236 (BC_1, IO45, input, X)," &
" 237 (BC_1, *, internal, 1)," & -- IO46.T
" 238 (BC_1, *, internal, X)," & -- IO46.O
" 239 (BC_1, *, internal, X)," & -- IO46.I
" 240 (BC_1, *, internal, 1)," & -- IO47.T
" 241 (BC_1, *, internal, X)," & -- IO47.O
" 242 (BC_1, *, internal, X)," & -- IO47.I
" 243 (BC_1, *, internal, 1)," & -- IO48.T
" 244 (BC_1, *, internal, X)," & -- IO48.O
" 245 (BC_1, *, internal, X)," & -- IO48.I
" 246 (BC_1, *, controlr, 1)," &
" 247 (BC_1, IO49, output3, X, 246, 1, PULL1)," &
" 248 (BC_1, IO49, input, X)," &
" 249 (BC_1, *, controlr, 1)," &
" 250 (BC_1, IO50, output3, X, 249, 1, PULL1)," &
" 251 (BC_1, IO50, input, X)," &
" 252 (BC_1, *, internal, X)," &
" 253 (BC_1, *, internal, X)," &
" 254 (BC_1, *, internal, X)," &
" 255 (BC_1, *, internal, X)," &
" 256 (BC_1, *, internal, X)," &
" 257 (BC_1, *, internal, X)," &
" 258 (BC_1, *, controlr, 1)," &
" 259 (BC_1, M1, output3, X, 258, 1, PULL1)," &
" 260 (BC_1, M1, input, X)," &
" 261 (BC_1, *, controlr, 1)," &
" 262 (BC_1, M0, output3, X, 261, 1, PULL1)," &
" 263 (BC_1, M0, input, X)," &
" 264 (BC_1, *, controlr, 1)," &
" 265 (BC_1, M2, output3, X, 264, 1, PULL1)," &
" 266 (BC_1, M2, input, X)," &
" 267 (BC_1, *, controlr, 1)," &
" 268 (BC_1, IO56, output3, X, 267, 1, PULL1)," &
" 269 (BC_1, IO56, input, X)," &
" 270 (BC_1, *, internal, X)," &
" 271 (BC_1, *, internal, X)," &
" 272 (BC_1, *, internal, X)," &
" 273 (BC_1, *, internal, X)," &
" 274 (BC_1, *, internal, X)," &
" 275 (BC_1, *, internal, X)," &
" 276 (BC_1, *, controlr, 1)," &
" 277 (BC_1, IO57, output3, X, 276, 1, PULL1)," &
" 278 (BC_1, IO57, input, X)," &
" 279 (BC_1, *, internal, 1)," & -- IO58.T
" 280 (BC_1, *, internal, X)," & -- IO58.O
" 281 (BC_1, *, internal, X)," & -- IO58.I
" 282 (BC_1, *, internal, 1)," & -- IO59.T
" 283 (BC_1, *, internal, X)," & -- IO59.O
" 284 (BC_1, *, internal, X)," & -- IO59.I
" 285 (BC_1, *, internal, X)," &
" 286 (BC_1, *, internal, X)," &
" 287 (BC_1, *, internal, X)," &
" 288 (BC_1, *, internal, 1)," & -- IO60.T
" 289 (BC_1, *, internal, X)," & -- IO60.O
" 290 (BC_1, *, internal, X)," & -- IO60.I
" 291 (BC_1, *, controlr, 1)," &
" 292 (BC_1, IO61, output3, X, 291, 1, PULL1)," &
" 293 (BC_1, IO61, input, X)," &
" 294 (BC_1, *, internal, 1)," & -- IO62.T
" 295 (BC_1, *, internal, X)," & -- IO62.O
" 296 (BC_1, *, internal, X)," & -- IO62.I
" 297 (BC_1, *, internal, X)," &
" 298 (BC_1, *, internal, X)," &
" 299 (BC_1, *, internal, X)," &
" 300 (BC_1, *, internal, 1)," & -- IO63.T
" 301 (BC_1, *, internal, X)," & -- IO63.O
" 302 (BC_1, *, internal, X)," & -- IO63.I
" 303 (BC_1, *, internal, 1)," & -- IO64.T
" 304 (BC_1, *, internal, X)," & -- IO64.O
" 305 (BC_1, *, internal, X)," & -- IO64.I
" 306 (BC_1, *, internal, 1)," & -- IO65.T
" 307 (BC_1, *, internal, X)," & -- IO65.O
" 308 (BC_1, *, internal, X)," & -- IO65.I
" 309 (BC_1, *, internal, X)," &
" 310 (BC_1, *, internal, X)," &
" 311 (BC_1, *, internal, X)," &
" 312 (BC_1, *, controlr, 1)," &
" 313 (BC_1, IO66, output3, X, 312, 1, PULL1)," &
" 314 (BC_1, IO66, input, X)," &
" 315 (BC_1, *, controlr, 1)," &
" 316 (BC_1, IO67, output3, X, 315, 1, PULL1)," &
" 317 (BC_1, IO67, input, X)," &
" 318 (BC_1, *, internal, 1)," & -- IO68.T
" 319 (BC_1, *, internal, X)," & -- IO68.O
" 320 (BC_1, *, internal, X)," & -- IO68.I
" 321 (BC_1, *, internal, X)," &
" 322 (BC_1, *, internal, X)," &
" 323 (BC_1, *, internal, X)," &
" 324 (BC_1, *, internal, 1)," & -- IO69.T
" 325 (BC_1, *, internal, X)," & -- IO69.O
" 326 (BC_1, *, internal, X)," & -- IO69.I
" 327 (BC_1, *, controlr, 1)," &
" 328 (BC_1, IO70, output3, X, 327, 1, PULL1)," &
" 329 (BC_1, IO70, input, X)," &
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the following line.
-- Repeat for registers 330 through 332.
-- " 330 (BC_1, *, controlr, 1)," &
" 330 (BC_1, *, internal, 1)," &
-- " 331 (BC_1, INIT, output3, X, 330, 1, PULL1)," &
" 331 (BC_1, *, internal, 0)," &
-- " 332 (BC_1, INIT, input, X)," &
" 332 (BC_1, *, internal, X)," &
" 333 (BC_1, *, internal, X)," &
" 334 (BC_1, *, internal, X)," &
" 335 (BC_1, *, internal, X)," &
" 336 (BC_1, *, controlr, 1)," &
" 337 (BC_1, IO74, output3, X, 336, 1, PULL1)," &
" 338 (BC_1, IO74, input, X)," &
" 339 (BC_1, *, controlr, 1)," &
" 340 (BC_1, IO75, output3, X, 339, 1, PULL1)," &
" 341 (BC_1, IO75, input, X)," &
" 342 (BC_1, *, internal, X)," &
" 343 (BC_1, *, internal, X)," &
" 344 (BC_1, *, internal, X)," &
" 345 (BC_1, *, internal, X)," &
" 346 (BC_1, *, internal, X)," &
" 347 (BC_1, *, internal, X)," &
" 348 (BC_1, *, internal, 1)," & -- IO76.T
" 349 (BC_1, *, internal, X)," & -- IO76.O
" 350 (BC_1, *, internal, X)," & -- IO76.I
" 351 (BC_1, *, internal, 1)," & -- IO77.T
" 352 (BC_1, *, internal, X)," & -- IO77.O
" 353 (BC_1, *, internal, X)," & -- IO77.I
" 354 (BC_1, *, controlr, 1)," &
" 355 (BC_1, IO78, output3, X, 354, 1, PULL1)," &
" 356 (BC_1, IO78, input, X)," &
" 357 (BC_1, *, internal, X)," &
" 358 (BC_1, *, internal, X)," &
" 359 (BC_1, *, internal, X)," &
" 360 (BC_1, *, controlr, 1)," &
" 361 (BC_1, IO79, output3, X, 360, 1, PULL1)," &
" 362 (BC_1, IO79, input, X)," &
" 363 (BC_1, *, internal, 1)," & -- IO80.T
" 364 (BC_1, *, internal, X)," & -- IO80.O
" 365 (BC_1, *, internal, X)," & -- IO80.I
" 366 (BC_1, *, internal, 1)," & -- IO81.T
" 367 (BC_1, *, internal, X)," & -- IO81.O
" 368 (BC_1, *, internal, X)," & -- IO81.I
" 369 (BC_1, *, internal, X)," &
" 370 (BC_1, *, internal, X)," &
" 371 (BC_1, *, internal, X)," &
" 372 (BC_1, *, internal, 1)," & -- IO82.T
" 373 (BC_1, *, internal, X)," & -- IO82.O
" 374 (BC_1, *, internal, X)," & -- IO82.I
" 375 (BC_1, *, internal, 1)," & -- IO83.T
" 376 (BC_1, *, internal, X)," & -- IO83.O
" 377 (BC_1, *, internal, X)," & -- IO83.I
" 378 (BC_1, *, controlr, 1)," &
" 379 (BC_1, IO84, output3, X, 378, 1, PULL1)," &
" 380 (BC_1, IO84, input, X)," &
" 381 (BC_1, *, internal, X)," &
" 382 (BC_1, *, internal, X)," &
" 383 (BC_1, *, internal, X)," &
" 384 (BC_1, *, controlr, 1)," &
" 385 (BC_1, IO85, output3, X, 384, 1, PULL1)," &
" 386 (BC_1, IO85, input, X)," &
" 387 (BC_1, *, internal, 1)," & -- IO86.T
" 388 (BC_1, *, internal, X)," & -- IO86.O
" 389 (BC_1, *, internal, X)," & -- IO86.I
" 390 (BC_1, *, internal, 1)," & -- IO87.T
" 391 (BC_1, *, internal, X)," & -- IO87.O
" 392 (BC_1, *, internal, X)," & -- IO87.I
" 393 (BC_1, *, internal, X)," &
" 394 (BC_1, *, internal, X)," &
" 395 (BC_1, *, internal, X)," &
" 396 (BC_1, *, controlr, 1)," &
" 397 (BC_1, IO88, output3, X, 396, 1, PULL1)," &
" 398 (BC_1, IO88, input, X)," &
" 399 (BC_1, *, controlr, 1)," &
" 400 (BC_1, IO89, output3, X, 399, 1, PULL1)," &
" 401 (BC_1, IO89, input, X)," &
" 402 (BC_1, *, internal, X)," &
" 403 (BC_1, *, internal, X)," &
" 404 (BC_1, *, internal, X)," &
" 405 (BC_1, *, internal, X)," &
" 406 (BC_1, *, internal, X)," &
" 407 (BC_1, *, internal, X)," &
" 408 (BC_1, *, controlr, 1)," &
" 409 (BC_1, IO94, output3, X, 408, 1, PULL1)," &
" 410 (BC_1, IO94, input, X)," &
" 411 (BC_1, *, controlr, 1)," &
" 412 (BC_1, IO95, output3, X, 411, 1, PULL1)," &
" 413 (BC_1, IO95, input, X)," &
" 414 (BC_1, *, internal, X)," &
" 415 (BC_1, *, internal, X)," &
" 416 (BC_1, *, internal, X)," &
" 417 (BC_1, *, internal, X)," &
" 418 (BC_1, *, internal, X)," &
" 419 (BC_1, *, internal, X)," &
" 420 (BC_1, *, internal, 1)," & -- IO96.T
" 421 (BC_1, *, internal, X)," & -- IO96.O
" 422 (BC_1, *, internal, X)," & -- IO96.I
" 423 (BC_1, *, internal, 1)," & -- IO97.T
" 424 (BC_1, *, internal, X)," & -- IO97.O
" 425 (BC_1, *, internal, X)," & -- IO97.I
" 426 (BC_1, *, controlr, 1)," &
" 427 (BC_1, IO98, output3, X, 426, 1, PULL1)," &
" 428 (BC_1, IO98, input, X)," &
" 429 (BC_1, *, internal, X)," &
" 430 (BC_1, *, internal, X)," &
" 431 (BC_1, *, internal, X)," &
" 432 (BC_1, *, internal, 1)," & -- IO99.T
" 433 (BC_1, *, internal, X)," & -- IO99.O
" 434 (BC_1, *, internal, X)," & -- IO99.I
" 435 (BC_1, *, internal, 1)," & -- IO100.T
" 436 (BC_1, *, internal, X)," & -- IO100.O
" 437 (BC_1, *, internal, X)," & -- IO100.I
" 438 (BC_1, *, internal, 1)," & -- IO101.T
" 439 (BC_1, *, internal, X)," & -- IO101.O
" 440 (BC_1, *, internal, X)," & -- IO101.I
" 441 (BC_1, *, internal, X)," &
" 442 (BC_1, *, internal, X)," &
" 443 (BC_1, *, internal, X)," &
" 444 (BC_1, *, controlr, 1)," &
" 445 (BC_1, IO102, output3, X, 444, 1, PULL1)," &
" 446 (BC_1, IO102, input, X)," &
" 447 (BC_1, *, controlr, 1)," &
" 448 (BC_1, IO103, output3, X, 447, 1, PULL1)," &
" 449 (BC_1, IO103, input, X)," &
" 450 (BC_1, *, internal, 1)," & -- IO104.T
" 451 (BC_1, *, internal, X)," & -- IO104.O
" 452 (BC_1, *, internal, X)," & -- IO104.I
" 453 (BC_1, *, internal, X)," &
" 454 (BC_1, *, internal, X)," &
" 455 (BC_1, *, internal, X)," &
" 456 (BC_1, *, internal, 1)," & -- IO105.T
" 457 (BC_1, *, internal, X)," & -- IO105.O
" 458 (BC_1, *, internal, X)," & -- IO105.I
" 459 (BC_1, *, controlr, 1)," &
" 460 (BC_1, IO106, output3, X, 459, 1, PULL1)," &
" 461 (BC_1, IO106, input, X)," &
" 462 (BC_1, *, controlr, 1)," &
" 463 (BC_1, IO107, output3, X, 462, 1, PULL1)," &
" 464 (BC_1, IO107, input, X)," &
" 465 (BC_1, *, internal, X)," &
" 466 (BC_1, *, internal, X)," &
" 467 (BC_1, *, internal, X)," &
" 468 (BC_1, *, controlr, 1)," &
" 469 (BC_1, IO110, output3, X, 468, 1, PULL1)," &
" 470 (BC_1, IO110, input, X)," &
" 471 (BC_1, *, controlr, 1)," &
" 472 (BC_1, IO111, output3, X, 471, 1, PULL1)," &
" 473 (BC_1, IO111, input, X)," &
" 474 (BC_1, *, internal, 1)," & -- IO112.T
" 475 (BC_1, *, internal, X)," & -- IO112.O
" 476 (BC_1, *, internal, X)," & -- IO112.I
" 477 (BC_1, *, internal, X)," &
" 478 (BC_1, *, internal, X)," &
" 479 (BC_1, *, internal, X)," &
" 480 (BC_1, *, internal, 1)," & -- IO113.T
" 481 (BC_1, *, internal, X)," & -- IO113.O
" 482 (BC_1, *, internal, X)," & -- IO113.I
" 483 (BC_1, *, controlr, 1)," &
" 484 (BC_1, IO114, output3, X, 483, 1, PULL1)," &
" 485 (BC_1, IO114, input, X)," &
" 486 (BC_1, *, controlr, 1)," &
" 487 (BC_1, IO115, output3, X, 486, 1, PULL1)," &
" 488 (BC_1, IO115, input, X)," &
" 489 (BC_1, *, internal, X)," &
" 490 (BC_1, *, internal, X)," &
" 491 (BC_1, *, internal, X)," &
" 492 (BC_1, *, internal, 1)," & -- IO116.T
" 493 (BC_1, *, internal, X)," & -- IO116.O
" 494 (BC_1, *, internal, X)," & -- IO116.I
" 495 (BC_1, *, internal, 1)," & -- IO117.T
" 496 (BC_1, *, internal, X)," & -- IO117.O
" 497 (BC_1, *, internal, X)," & -- IO117.I
" 498 (BC_1, *, controlr, 1)," &
" 499 (BC_1, IO118, output3, X, 498, 1, PULL1)," &
" 500 (BC_1, IO118, input, X)," &
" 501 (BC_1, *, internal, X)," &
" 502 (BC_1, *, internal, X)," &
" 503 (BC_1, *, internal, X)," &
" 504 (BC_1, *, controlr, 1)," &
" 505 (BC_1, IO119, output3, X, 504, 1, PULL1)," &
" 506 (BC_1, IO119, input, X)," &
" 507 (BC_1, *, internal, 1)," & -- IO120.T
" 508 (BC_1, *, internal, X)," & -- IO120.O
" 509 (BC_1, *, internal, X)," & -- IO120.I
" 510 (BC_1, *, internal, 1)," & -- IO121.T
" 511 (BC_1, *, internal, X)," & -- IO121.O
" 512 (BC_1, *, internal, X)," & -- IO121.I
" 513 (BC_1, *, internal, X)," &
" 514 (BC_1, *, internal, X)," &
" 515 (BC_1, *, internal, X)," &
" 516 (BC_1, *, controlr, 1)," &
" 517 (BC_1, IO122, output3, X, 516, 1, PULL1)," &
" 518 (BC_1, IO122, input, X)," &
" 519 (BC_1, *, controlr, 1)," &
" 520 (BC_1, IO123, output3, X, 519, 1, PULL1)," &
" 521 (BC_1, IO123, input, X)," &
" 522 (BC_1, *, internal, X)," &
" 523 (BC_1, *, internal, X)," &
" 524 (BC_1, *, internal, X)," &
" 525 (BC_1, *, internal, X)," &
" 526 (BC_1, *, internal, X)," &
" 527 (BC_1, *, internal, X)," &
" 528 (BC_1, *, internal, X)";
--end boundary register
attribute DESIGN_WARNING of XC5204_PC84 : entity is
"CCLK and DONE are not represented in BOUNDARY_REGISTER." &
"This BSDL file must be modified by the FPGA designer in order to" &
"reflect post-configuration behavior (if any)." &
"If INIT has been high or floating since power-on or the last" &
"rising edge of PROGRAM, then the device may be in" &
"configuration mode in which case this file is not valid." &
"Programmably inverted input paths are controlled with the" &
"wrong polarity." &
"The tristate control is not captured properly when GTS is activated." &
"Some pins have both controlled and uncontrolled input paths.";
end XC5204_PC84;
