--$ XILINX$RCSfile: xc5206_tq176.bsd,v $
--$ XILINX$Revision: 1.3 $
--
-- BSDL file for device XC5206, package TQ176
-- Xilinx, Inc. $State: FINAL $ $Date: 1997-11-12 21:36:15+00 $
-- Generated by createBSDL 2.6
--
-- For technical support, contact Xilinx as follows:
-- North America 1-800-255-7778 hotline@xilinx.com
-- United Kingdom (44) 1932 820821 ukhelp@xilinx.com
-- France (33) 1 3463 0100 frhelp@xilinx.com
-- Germany (49) 89 991 54930 dlhelp@xilinx.com
-- Japan (81) 3-3297-9163 jhotline@xilinx.com
--
-- BSDL verified to conform to 1149.1b-1994 syntax. This device has been
-- tested by the Intellitech 1149.1 Verification Lab using the Intellitech
-- Eclipse(TM) Scan Diagnostic Tool and the Intellitech RCT(TM). This
-- device has been verified to operate according to the BSDL provided,
-- and is compatible with the IEEE 1149.1 standard when the operating
-- instructions in the BSDL are followed.
-- PH: 603-868-7116 or email: scansupport@intellitech.com
--
-- This BSDL file reflects the pre-configuration JTAG behavior. To reflect
-- the post-configuration JTAG behavior (if any), edit this file as described
-- below. Many of these changes are demonstrated by commented-out template
-- lines preceeding the lines they would replace:
--
-- 1. Enable USER instructions as appropriate (see below).
-- 2. For inputs using uncontrolled paths (e.g. PGCK), change
-- boundary cell function from 'input' to 'clock' or 'observe_only'.
-- 3. Set disable result of all pads as configured.
-- 4. Set safe state of boundary cells as necessary.
-- 5. Set safe state of INIT output to X, or as necessary (see below).
-- 6. Rename entity if necessary to avoid name collisions.
-- 7. Change INIT port direction from "in" to "inout" (see below).
-- 8. Change COMPLIANCE_PATTERNS to "(PROGRAM) (1)" (see below).
-- 9. Change INIT boundary cells from internal to controlr, output3,
-- and input, respectively (see below).
-- 10. Remove the design warning regarding keeping INIT low.
--
-- NOTE: Post-configuration JTAG is available only if the BSCAN symbol
-- is instantiated in the FPGA design.
-- NOTE: PULLUP symbols must be instantiated on the TMS and TDI pins
-- in the FPGA design to comply with IEEE Std. 1149.1-1993.
entity XC5206_TQ176 is
generic (PHYSICAL_PIN_MAP : string := "TQ176" );
port (
CCLK: linkage bit;
DONE: linkage bit;
GND: linkage bit_vector (1 to 16);
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the following line so
-- that INIT is of type inout.
-- INIT: inout bit;
INIT: in bit;
IO3: inout bit;
IO4: inout bit;
IO5: inout bit;
IO6: inout bit;
IO7: inout bit;
IO8: inout bit;
IO9: inout bit;
IO10: inout bit;
IO11: inout bit;
IO12: inout bit;
IO14: inout bit;
IO15: inout bit;
IO16: inout bit;
IO17: inout bit;
IO18: inout bit;
IO19: inout bit;
IO20: inout bit;
IO21: inout bit;
IO24: inout bit;
IO25: inout bit;
IO26: inout bit;
IO27: inout bit;
IO30: inout bit;
IO31: inout bit;
IO33: inout bit;
IO34: inout bit;
IO36: inout bit;
IO37: inout bit;
IO38: inout bit;
IO39: inout bit;
IO40: inout bit;
IO41: inout bit;
IO42: inout bit;
IO45: inout bit;
IO46: inout bit;
IO47: inout bit;
IO48: inout bit;
IO49: inout bit;
IO50: inout bit;
IO51: inout bit;
IO52: inout bit;
IO53: inout bit;
IO54: inout bit;
IO56: inout bit;
IO57: inout bit;
IO58: inout bit;
IO59: inout bit;
IO60: inout bit;
IO61: inout bit;
IO62: inout bit;
IO63: inout bit;
IO69: inout bit;
IO70: inout bit;
IO71: inout bit;
IO72: inout bit;
IO73: inout bit;
IO74: inout bit;
IO75: inout bit;
IO76: inout bit;
IO78: inout bit;
IO79: inout bit;
IO80: inout bit;
IO81: inout bit;
IO82: inout bit;
IO83: inout bit;
IO84: inout bit;
IO85: inout bit;
IO86: inout bit;
IO90: inout bit;
IO91: inout bit;
IO92: inout bit;
IO93: inout bit;
IO94: inout bit;
IO95: inout bit;
IO96: inout bit;
IO97: inout bit;
IO98: inout bit;
IO99: inout bit;
IO101: inout bit;
IO102: inout bit;
IO103: inout bit;
IO104: inout bit;
IO105: inout bit;
IO106: inout bit;
IO107: inout bit;
IO108: inout bit;
IO113: inout bit;
IO114: inout bit;
IO115: inout bit;
IO116: inout bit;
IO117: inout bit;
IO118: inout bit;
IO119: inout bit;
IO120: inout bit;
IO122: inout bit;
IO123: inout bit;
IO124: inout bit;
IO125: inout bit;
IO126: inout bit;
IO127: inout bit;
IO128: inout bit;
IO129: inout bit;
IO130: inout bit;
IO131: inout bit;
IO134: inout bit;
IO135: inout bit;
IO136: inout bit;
IO137: inout bit;
IO138: inout bit;
IO139: inout bit;
IO140: inout bit;
IO141: inout bit;
IO142: inout bit;
IO143: inout bit;
IO145: inout bit;
IO146: inout bit;
IO147: inout bit;
IO148: inout bit;
IO149: inout bit;
IO150: inout bit;
IO151: inout bit;
IO152: inout bit;
IO157: inout bit;
IO158: inout bit;
IO159: inout bit;
IO160: inout bit;
IO161: inout bit;
IO162: inout bit;
IO163: inout bit;
IO164: inout bit;
IO166: inout bit;
IO167: inout bit;
IO168: inout bit;
IO169: inout bit;
IO170: inout bit;
IO171: inout bit;
IO172: inout bit;
IO173: inout bit;
IO174: inout bit;
IO175: inout bit;
M0: inout bit;
M1: inout bit;
M2: inout bit;
PROGRAM: in bit;
TCK: in bit;
TDI: in bit;
TDO: out bit;
TMS: in bit;
VDD: linkage bit_vector (1 to 8)
); --end port list
use STD_1149_1_1994.all;
attribute COMPONENT_CONFORMANCE of XC5206_TQ176 : entity is
"STD_1149_1_1993";
attribute PIN_MAP of XC5206_TQ176 : entity is PHYSICAL_PIN_MAP;
constant TQ176: PIN_MAP_STRING:=
"CCLK:131," &
"DONE:88," &
"GND:(154,166,1,10,21,33,43,55,67,78," &
"87,99,111,122,134,143)," &
"INIT:65," &
"IO3:156," &
"IO4:157," &
"IO5:158," &
"IO6:159," &
"IO7:160," &
"IO8:161," &
"IO9:162," &
"IO10:163," &
"IO11:164," &
"IO12:165," &
"IO14:168," &
"IO15:169," &
"IO16:170," &
"IO17:171," &
"IO18:172," &
"IO19:173," &
"IO20:174," &
"IO21:175," &
"IO24:2," &
"IO25:3," &
"IO26:4," &
"IO27:5," &
"IO30:8," &
"IO31:9," &
"IO33:11," &
"IO34:12," &
"IO36:14," &
"IO37:15," &
"IO38:16," &
"IO39:17," &
"IO40:18," &
"IO41:19," &
"IO42:20," &
"IO45:23," &
"IO46:24," &
"IO47:25," &
"IO48:26," &
"IO49:27," &
"IO50:28," &
"IO51:29," &
"IO52:30," &
"IO53:31," &
"IO54:32," &
"IO56:34," &
"IO57:35," &
"IO58:36," &
"IO59:37," &
"IO60:38," &
"IO61:39," &
"IO62:40," &
"IO63:41," &
"IO69:47," &
"IO70:48," &
"IO71:49," &
"IO72:50," &
"IO73:51," &
"IO74:52," &
"IO75:53," &
"IO76:54," &
"IO78:56," &
"IO79:57," &
"IO80:58," &
"IO81:59," &
"IO82:60," &
"IO83:61," &
"IO84:62," &
"IO85:63," &
"IO86:64," &
"IO90:68," &
"IO91:69," &
"IO92:70," &
"IO93:71," &
"IO94:72," &
"IO95:73," &
"IO96:74," &
"IO97:75," &
"IO98:76," &
"IO99:77," &
"IO101:79," &
"IO102:80," &
"IO103:81," &
"IO104:82," &
"IO105:83," &
"IO106:84," &
"IO107:85," &
"IO108:86," &
"IO113:91," &
"IO114:92," &
"IO115:93," &
"IO116:94," &
"IO117:95," &
"IO118:96," &
"IO119:97," &
"IO120:98," &
"IO122:100," &
"IO123:101," &
"IO124:102," &
"IO125:103," &
"IO126:104," &
"IO127:105," &
"IO128:106," &
"IO129:107," &
"IO130:108," &
"IO131:109," &
"IO134:112," &
"IO135:113," &
"IO136:114," &
"IO137:115," &
"IO138:116," &
"IO139:117," &
"IO140:118," &
"IO141:119," &
"IO142:120," &
"IO143:121," &
"IO145:123," &
"IO146:124," &
"IO147:125," &
"IO148:126," &
"IO149:127," &
"IO150:128," &
"IO151:129," &
"IO152:130," &
"IO157:135," &
"IO158:136," &
"IO159:137," &
"IO160:138," &
"IO161:139," &
"IO162:140," &
"IO163:141," &
"IO164:142," &
"IO166:144," &
"IO167:145," &
"IO168:146," &
"IO169:147," &
"IO170:148," &
"IO171:149," &
"IO172:150," &
"IO173:151," &
"IO174:152," &
"IO175:153," &
"M0:44," &
"M1:42," &
"M2:46," &
"PROGRAM:90," &
"TCK:7," &
"TDI:6," &
"TDO:133," &
"TMS:13," &
"VDD:(155,176,22,45,66,89,110,132)";
--end pin map
attribute TAP_SCAN_IN of TDI : signal is true;
attribute TAP_SCAN_MODE of TMS : signal is true;
attribute TAP_SCAN_OUT of TDO : signal is true;
attribute TAP_SCAN_CLOCK of TCK : signal is (2.0e6, LOW);
-- This is conservative. Real max is expected to be (~5MHz, BOTH).
attribute COMPLIANCE_PATTERNS of XC5206_TQ176 : entity is
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the corresponding line
-- below.
-- "(PROGRAM) (1)";
--
-- NOTE: If INIT has been high or floating since the later of power-on
-- and the last rising transition of PROGRAM, then the device may
-- be in configuration mode in which case some JTAG instructions
-- will not be available.
"(INIT,PROGRAM) (01)";
attribute INSTRUCTION_LENGTH of XC5206_TQ176 : entity is 3;
attribute INSTRUCTION_OPCODE of XC5206_TQ176 : entity is
"RESERVED (110)," &
"READBACK (100)," & -- Not available during configuration
"CONFIGURE (101)," & -- Not available during configuration
"USER2 (011)," & -- Not available until after configuration
"USER1 (010)," & -- Not available until after configuration
"SAMPLE (001)," & -- Internal capture not valid until after config
"EXTEST (000)," & -- Not available during configuration
"BYPASS (111)";
attribute INSTRUCTION_CAPTURE of XC5206_TQ176 : entity is "X01";
-- MSB of instruction capture is low during configuration.
-- If the device is configured, and a USER instruction is implemented
-- and not private to the FPGA designer, then it should be removed
-- from INSTRUCTION_PRIVATE, and the target register should be defined
-- in REGISTER_ACCESS.
attribute INSTRUCTION_PRIVATE of XC5206_TQ176 : entity is
"USER1," &
"USER2," &
"READBACK," &
"RESERVED," &
"CONFIGURE";
attribute REGISTER_ACCESS of XC5206_TQ176 : entity is
-- "<reg_name>[<length>] (USER1)," &
-- "<reg_name>[<length>] (USER2)," &
"BYPASS (BYPASS)," &
"BOUNDARY (SAMPLE,EXTEST)";
attribute BOUNDARY_LENGTH of XC5206_TQ176 : entity is 673;
attribute BOUNDARY_REGISTER of XC5206_TQ176 : entity is
-- cellnum (type, port, function, safe[, ccell, disval, disrslt])
" 0 (BC_1, *, internal, X)," &
" 1 (BC_1, *, internal, X)," &
" 2 (BC_1, *, internal, X)," &
" 3 (BC_1, *, internal, X)," &
" 4 (BC_1, *, internal, X)," &
" 5 (BC_1, *, internal, X)," &
" 6 (BC_1, *, internal, X)," &
" 7 (BC_1, *, internal, X)," &
" 8 (BC_1, *, internal, X)," &
" 9 (BC_1, *, controlr, 1)," &
" 10 (BC_1, IO157, output3, X, 9, 1, PULL1)," &
" 11 (BC_1, IO157, input, X)," &
" 12 (BC_1, *, internal, X)," &
" 13 (BC_1, *, internal, X)," &
" 14 (BC_1, *, internal, X)," &
" 15 (BC_1, *, controlr, 1)," &
" 16 (BC_1, IO158, output3, X, 15, 1, PULL1)," &
" 17 (BC_1, IO158, input, X)," &
" 18 (BC_1, *, controlr, 1)," &
" 19 (BC_1, IO159, output3, X, 18, 1, PULL1)," &
" 20 (BC_1, IO159, input, X)," &
" 21 (BC_1, *, controlr, 1)," &
" 22 (BC_1, IO160, output3, X, 21, 1, PULL1)," &
" 23 (BC_1, IO160, input, X)," &
" 24 (BC_1, *, internal, X)," &
" 25 (BC_1, *, internal, X)," &
" 26 (BC_1, *, internal, X)," &
" 27 (BC_1, *, controlr, 1)," &
" 28 (BC_1, IO161, output3, X, 27, 1, PULL1)," &
" 29 (BC_1, IO161, input, X)," &
" 30 (BC_1, *, controlr, 1)," &
" 31 (BC_1, IO162, output3, X, 30, 1, PULL1)," &
" 32 (BC_1, IO162, input, X)," &
" 33 (BC_1, *, controlr, 1)," &
" 34 (BC_1, IO163, output3, X, 33, 1, PULL1)," &
" 35 (BC_1, IO163, input, X)," &
" 36 (BC_1, *, internal, X)," &
" 37 (BC_1, *, internal, X)," &
" 38 (BC_1, *, internal, X)," &
" 39 (BC_1, *, internal, X)," &
" 40 (BC_1, *, internal, X)," &
" 41 (BC_1, *, internal, X)," &
" 42 (BC_1, *, controlr, 1)," &
" 43 (BC_1, IO164, output3, X, 42, 1, PULL1)," &
" 44 (BC_1, IO164, input, X)," &
" 45 (BC_1, *, controlr, 1)," &
" 46 (BC_1, IO166, output3, X, 45, 1, PULL1)," &
" 47 (BC_1, IO166, input, X)," &
" 48 (BC_1, *, internal, X)," &
" 49 (BC_1, *, internal, X)," &
" 50 (BC_1, *, internal, X)," &
" 51 (BC_1, *, controlr, 1)," &
" 52 (BC_1, IO167, output3, X, 51, 1, PULL1)," &
" 53 (BC_1, IO167, input, X)," &
" 54 (BC_1, *, controlr, 1)," &
" 55 (BC_1, IO168, output3, X, 54, 1, PULL1)," &
" 56 (BC_1, IO168, input, X)," &
" 57 (BC_1, *, controlr, 1)," &
" 58 (BC_1, IO169, output3, X, 57, 1, PULL1)," &
" 59 (BC_1, IO169, input, X)," &
" 60 (BC_1, *, internal, X)," &
" 61 (BC_1, *, internal, X)," &
" 62 (BC_1, *, internal, X)," &
" 63 (BC_1, *, controlr, 1)," &
" 64 (BC_1, IO170, output3, X, 63, 1, PULL1)," &
" 65 (BC_1, IO170, input, X)," &
" 66 (BC_1, *, controlr, 1)," &
" 67 (BC_1, IO171, output3, X, 66, 1, PULL1)," &
" 68 (BC_1, IO171, input, X)," &
" 69 (BC_1, *, controlr, 1)," &
" 70 (BC_1, IO172, output3, X, 69, 1, PULL1)," &
" 71 (BC_1, IO172, input, X)," &
" 72 (BC_1, *, internal, X)," &
" 73 (BC_1, *, internal, X)," &
" 74 (BC_1, *, internal, X)," &
" 75 (BC_1, *, controlr, 1)," &
" 76 (BC_1, IO173, output3, X, 75, 1, PULL1)," &
" 77 (BC_1, IO173, input, X)," &
" 78 (BC_1, *, controlr, 1)," &
" 79 (BC_1, IO174, output3, X, 78, 1, PULL1)," &
" 80 (BC_1, IO174, input, X)," &
" 81 (BC_1, *, controlr, 1)," &
" 82 (BC_1, IO175, output3, X, 81, 1, PULL1)," &
" 83 (BC_1, IO175, input, X)," &
" 84 (BC_1, *, internal, X)," &
" 85 (BC_1, *, internal, X)," &
" 86 (BC_1, *, internal, X)," &
" 87 (BC_1, *, controlr, 1)," &
" 88 (BC_1, IO3, output3, X, 87, 1, PULL1)," &
" 89 (BC_1, IO3, input, X)," &
" 90 (BC_1, *, controlr, 1)," &
" 91 (BC_1, IO4, output3, X, 90, 1, PULL1)," &
" 92 (BC_1, IO4, input, X)," &
" 93 (BC_1, *, controlr, 1)," &
" 94 (BC_1, IO5, output3, X, 93, 1, PULL1)," &
" 95 (BC_1, IO5, input, X)," &
" 96 (BC_1, *, internal, X)," &
" 97 (BC_1, *, internal, X)," &
" 98 (BC_1, *, internal, X)," &
" 99 (BC_1, *, controlr, 1)," &
" 100 (BC_1, IO6, output3, X, 99, 1, PULL1)," &
" 101 (BC_1, IO6, input, X)," &
" 102 (BC_1, *, controlr, 1)," &
" 103 (BC_1, IO7, output3, X, 102, 1, PULL1)," &
" 104 (BC_1, IO7, input, X)," &
" 105 (BC_1, *, controlr, 1)," &
" 106 (BC_1, IO8, output3, X, 105, 1, PULL1)," &
" 107 (BC_1, IO8, input, X)," &
" 108 (BC_1, *, internal, X)," &
" 109 (BC_1, *, internal, X)," &
" 110 (BC_1, *, internal, X)," &
" 111 (BC_1, *, controlr, 1)," &
" 112 (BC_1, IO9, output3, X, 111, 1, PULL1)," &
" 113 (BC_1, IO9, input, X)," &
" 114 (BC_1, *, controlr, 1)," &
" 115 (BC_1, IO10, output3, X, 114, 1, PULL1)," &
" 116 (BC_1, IO10, input, X)," &
" 117 (BC_1, *, controlr, 1)," &
" 118 (BC_1, IO11, output3, X, 117, 1, PULL1)," &
" 119 (BC_1, IO11, input, X)," &
" 120 (BC_1, *, internal, X)," &
" 121 (BC_1, *, internal, X)," &
" 122 (BC_1, *, internal, X)," &
" 123 (BC_1, *, controlr, 1)," &
" 124 (BC_1, IO12, output3, X, 123, 1, PULL1)," &
" 125 (BC_1, IO12, input, X)," &
" 126 (BC_1, *, controlr, 1)," &
" 127 (BC_1, IO14, output3, X, 126, 1, PULL1)," &
" 128 (BC_1, IO14, input, X)," &
" 129 (BC_1, *, controlr, 1)," &
" 130 (BC_1, IO15, output3, X, 129, 1, PULL1)," &
" 131 (BC_1, IO15, input, X)," &
" 132 (BC_1, *, internal, X)," &
" 133 (BC_1, *, internal, X)," &
" 134 (BC_1, *, internal, X)," &
" 135 (BC_1, *, internal, X)," &
" 136 (BC_1, *, internal, X)," &
" 137 (BC_1, *, internal, X)," &
" 138 (BC_1, *, controlr, 1)," &
" 139 (BC_1, IO16, output3, X, 138, 1, PULL1)," &
" 140 (BC_1, IO16, input, X)," &
" 141 (BC_1, *, controlr, 1)," &
" 142 (BC_1, IO17, output3, X, 141, 1, PULL1)," &
" 143 (BC_1, IO17, input, X)," &
" 144 (BC_1, *, internal, X)," &
" 145 (BC_1, *, internal, X)," &
" 146 (BC_1, *, internal, X)," &
" 147 (BC_1, *, internal, X)," &
" 148 (BC_1, *, internal, X)," &
" 149 (BC_1, *, internal, X)," &
" 150 (BC_1, *, controlr, 1)," &
" 151 (BC_1, IO18, output3, X, 150, 1, PULL1)," &
" 152 (BC_1, IO18, input, X)," &
" 153 (BC_1, *, controlr, 1)," &
" 154 (BC_1, IO19, output3, X, 153, 1, PULL1)," &
" 155 (BC_1, IO19, input, X)," &
" 156 (BC_1, *, internal, X)," &
" 157 (BC_1, *, internal, X)," &
" 158 (BC_1, *, internal, X)," &
" 159 (BC_1, *, internal, X)," &
" 160 (BC_1, *, internal, X)," &
" 161 (BC_1, *, internal, X)," &
" 162 (BC_1, *, controlr, 1)," &
" 163 (BC_1, IO20, output3, X, 162, 1, PULL1)," &
" 164 (BC_1, IO20, input, X)," &
" 165 (BC_1, *, controlr, 1)," &
" 166 (BC_1, IO21, output3, X, 165, 1, PULL1)," &
" 167 (BC_1, IO21, input, X)," &
" 168 (BC_1, *, internal, X)," &
" 169 (BC_1, *, internal, X)," &
" 170 (BC_1, *, internal, X)," &
" 171 (BC_1, *, internal, X)," &
" 172 (BC_1, *, internal, X)," &
" 173 (BC_1, *, internal, X)," &
" 174 (BC_1, *, controlr, 1)," &
" 175 (BC_1, IO24, output3, X, 174, 1, PULL1)," &
" 176 (BC_1, IO24, input, X)," &
" 177 (BC_1, *, controlr, 1)," &
" 178 (BC_1, IO25, output3, X, 177, 1, PULL1)," &
" 179 (BC_1, IO25, input, X)," &
" 180 (BC_1, *, internal, X)," &
" 181 (BC_1, *, internal, X)," &
" 182 (BC_1, *, internal, X)," &
" 183 (BC_1, *, controlr, 1)," &
" 184 (BC_1, IO26, output3, X, 183, 1, PULL1)," &
" 185 (BC_1, IO26, input, X)," &
" 186 (BC_1, *, controlr, 1)," &
" 187 (BC_1, IO27, output3, X, 186, 1, PULL1)," &
" 188 (BC_1, IO27, input, X)," &
" 189 (BC_1, *, internal, X)," &
" 190 (BC_1, *, internal, X)," &
" 191 (BC_1, *, internal, X)," &
" 192 (BC_1, *, internal, X)," &
" 193 (BC_1, *, internal, X)," &
" 194 (BC_1, *, internal, X)," &
" 195 (BC_1, *, internal, X)," &
" 196 (BC_1, *, internal, X)," &
" 197 (BC_1, *, internal, X)," &
" 198 (BC_1, *, controlr, 1)," &
" 199 (BC_1, IO30, output3, X, 198, 1, PULL1)," &
" 200 (BC_1, IO30, input, X)," &
" 201 (BC_1, *, controlr, 1)," &
" 202 (BC_1, IO31, output3, X, 201, 1, PULL1)," &
" 203 (BC_1, IO31, input, X)," &
" 204 (BC_1, *, internal, X)," &
" 205 (BC_1, *, internal, X)," &
" 206 (BC_1, *, internal, X)," &
" 207 (BC_1, *, controlr, 1)," &
" 208 (BC_1, IO33, output3, X, 207, 1, PULL1)," &
" 209 (BC_1, IO33, input, X)," &
" 210 (BC_1, *, controlr, 1)," &
" 211 (BC_1, IO34, output3, X, 210, 1, PULL1)," &
" 212 (BC_1, IO34, input, X)," &
" 213 (BC_1, *, internal, X)," &
" 214 (BC_1, *, internal, X)," &
" 215 (BC_1, *, internal, X)," &
" 216 (BC_1, *, internal, X)," &
" 217 (BC_1, *, internal, X)," &
" 218 (BC_1, *, internal, X)," &
" 219 (BC_1, *, controlr, 1)," &
" 220 (BC_1, IO36, output3, X, 219, 1, PULL1)," &
" 221 (BC_1, IO36, input, X)," &
" 222 (BC_1, *, controlr, 1)," &
" 223 (BC_1, IO37, output3, X, 222, 1, PULL1)," &
" 224 (BC_1, IO37, input, X)," &
" 225 (BC_1, *, controlr, 1)," &
" 226 (BC_1, IO38, output3, X, 225, 1, PULL1)," &
" 227 (BC_1, IO38, input, X)," &
" 228 (BC_1, *, internal, X)," &
" 229 (BC_1, *, internal, X)," &
" 230 (BC_1, *, internal, X)," &
" 231 (BC_1, *, internal, X)," &
" 232 (BC_1, *, internal, X)," &
" 233 (BC_1, *, internal, X)," &
" 234 (BC_1, *, controlr, 1)," &
" 235 (BC_1, IO39, output3, X, 234, 1, PULL1)," &
" 236 (BC_1, IO39, input, X)," &
" 237 (BC_1, *, controlr, 1)," &
" 238 (BC_1, IO40, output3, X, 237, 1, PULL1)," &
" 239 (BC_1, IO40, input, X)," &
" 240 (BC_1, *, internal, X)," &
" 241 (BC_1, *, internal, X)," &
" 242 (BC_1, *, internal, X)," &
" 243 (BC_1, *, internal, X)," &
" 244 (BC_1, *, internal, X)," &
" 245 (BC_1, *, internal, X)," &
" 246 (BC_1, *, controlr, 1)," &
" 247 (BC_1, IO41, output3, X, 246, 1, PULL1)," &
" 248 (BC_1, IO41, input, X)," &
" 249 (BC_1, *, controlr, 1)," &
" 250 (BC_1, IO42, output3, X, 249, 1, PULL1)," &
" 251 (BC_1, IO42, input, X)," &
" 252 (BC_1, *, internal, X)," &
" 253 (BC_1, *, internal, X)," &
" 254 (BC_1, *, internal, X)," &
" 255 (BC_1, *, controlr, 1)," &
" 256 (BC_1, IO45, output3, X, 255, 1, PULL1)," &
" 257 (BC_1, IO45, input, X)," &
" 258 (BC_1, *, controlr, 1)," &
" 259 (BC_1, IO46, output3, X, 258, 1, PULL1)," &
" 260 (BC_1, IO46, input, X)," &
" 261 (BC_1, *, controlr, 1)," &
" 262 (BC_1, IO47, output3, X, 261, 1, PULL1)," &
" 263 (BC_1, IO47, input, X)," &
" 264 (BC_1, *, internal, X)," &
" 265 (BC_1, *, internal, X)," &
" 266 (BC_1, *, internal, X)," &
" 267 (BC_1, *, controlr, 1)," &
" 268 (BC_1, IO48, output3, X, 267, 1, PULL1)," &
" 269 (BC_1, IO48, input, X)," &
" 270 (BC_1, *, controlr, 1)," &
" 271 (BC_1, IO49, output3, X, 270, 1, PULL1)," &
" 272 (BC_1, IO49, input, X)," &
" 273 (BC_1, *, controlr, 1)," &
" 274 (BC_1, IO50, output3, X, 273, 1, PULL1)," &
" 275 (BC_1, IO50, input, X)," &
" 276 (BC_1, *, internal, X)," &
" 277 (BC_1, *, internal, X)," &
" 278 (BC_1, *, internal, X)," &
" 279 (BC_1, *, controlr, 1)," &
" 280 (BC_1, IO51, output3, X, 279, 1, PULL1)," &
" 281 (BC_1, IO51, input, X)," &
" 282 (BC_1, *, controlr, 1)," &
" 283 (BC_1, IO52, output3, X, 282, 1, PULL1)," &
" 284 (BC_1, IO52, input, X)," &
" 285 (BC_1, *, controlr, 1)," &
" 286 (BC_1, IO53, output3, X, 285, 1, PULL1)," &
" 287 (BC_1, IO53, input, X)," &
" 288 (BC_1, *, internal, X)," &
" 289 (BC_1, *, internal, X)," &
" 290 (BC_1, *, internal, X)," &
" 291 (BC_1, *, controlr, 1)," &
" 292 (BC_1, IO54, output3, X, 291, 1, PULL1)," &
" 293 (BC_1, IO54, input, X)," &
" 294 (BC_1, *, controlr, 1)," &
" 295 (BC_1, IO56, output3, X, 294, 1, PULL1)," &
" 296 (BC_1, IO56, input, X)," &
" 297 (BC_1, *, controlr, 1)," &
" 298 (BC_1, IO57, output3, X, 297, 1, PULL1)," &
" 299 (BC_1, IO57, input, X)," &
" 300 (BC_1, *, internal, X)," &
" 301 (BC_1, *, internal, X)," &
" 302 (BC_1, *, internal, X)," &
" 303 (BC_1, *, controlr, 1)," &
" 304 (BC_1, IO58, output3, X, 303, 1, PULL1)," &
" 305 (BC_1, IO58, input, X)," &
" 306 (BC_1, *, controlr, 1)," &
" 307 (BC_1, IO59, output3, X, 306, 1, PULL1)," &
" 308 (BC_1, IO59, input, X)," &
" 309 (BC_1, *, controlr, 1)," &
" 310 (BC_1, IO60, output3, X, 309, 1, PULL1)," &
" 311 (BC_1, IO60, input, X)," &
" 312 (BC_1, *, internal, X)," &
" 313 (BC_1, *, internal, X)," &
" 314 (BC_1, *, internal, X)," &
" 315 (BC_1, *, controlr, 1)," &
" 316 (BC_1, IO61, output3, X, 315, 1, PULL1)," &
" 317 (BC_1, IO61, input, X)," &
" 318 (BC_1, *, controlr, 1)," &
" 319 (BC_1, IO62, output3, X, 318, 1, PULL1)," &
" 320 (BC_1, IO62, input, X)," &
" 321 (BC_1, *, controlr, 1)," &
" 322 (BC_1, IO63, output3, X, 321, 1, PULL1)," &
" 323 (BC_1, IO63, input, X)," &
" 324 (BC_1, *, internal, X)," &
" 325 (BC_1, *, internal, X)," &
" 326 (BC_1, *, internal, X)," &
" 327 (BC_1, *, internal, X)," &
" 328 (BC_1, *, internal, X)," &
" 329 (BC_1, *, internal, X)," &
" 330 (BC_1, *, controlr, 1)," &
" 331 (BC_1, M1, output3, X, 330, 1, PULL1)," &
" 332 (BC_1, M1, input, X)," &
" 333 (BC_1, *, controlr, 1)," &
" 334 (BC_1, M0, output3, X, 333, 1, PULL1)," &
" 335 (BC_1, M0, input, X)," &
" 336 (BC_1, *, controlr, 1)," &
" 337 (BC_1, M2, output3, X, 336, 1, PULL1)," &
" 338 (BC_1, M2, input, X)," &
" 339 (BC_1, *, controlr, 1)," &
" 340 (BC_1, IO69, output3, X, 339, 1, PULL1)," &
" 341 (BC_1, IO69, input, X)," &
" 342 (BC_1, *, internal, X)," &
" 343 (BC_1, *, internal, X)," &
" 344 (BC_1, *, internal, X)," &
" 345 (BC_1, *, internal, X)," &
" 346 (BC_1, *, internal, X)," &
" 347 (BC_1, *, internal, X)," &
" 348 (BC_1, *, controlr, 1)," &
" 349 (BC_1, IO70, output3, X, 348, 1, PULL1)," &
" 350 (BC_1, IO70, input, X)," &
" 351 (BC_1, *, controlr, 1)," &
" 352 (BC_1, IO71, output3, X, 351, 1, PULL1)," &
" 353 (BC_1, IO71, input, X)," &
" 354 (BC_1, *, controlr, 1)," &
" 355 (BC_1, IO72, output3, X, 354, 1, PULL1)," &
" 356 (BC_1, IO72, input, X)," &
" 357 (BC_1, *, internal, X)," &
" 358 (BC_1, *, internal, X)," &
" 359 (BC_1, *, internal, X)," &
" 360 (BC_1, *, controlr, 1)," &
" 361 (BC_1, IO73, output3, X, 360, 1, PULL1)," &
" 362 (BC_1, IO73, input, X)," &
" 363 (BC_1, *, controlr, 1)," &
" 364 (BC_1, IO74, output3, X, 363, 1, PULL1)," &
" 365 (BC_1, IO74, input, X)," &
" 366 (BC_1, *, internal, X)," &
" 367 (BC_1, *, internal, X)," &
" 368 (BC_1, *, internal, X)," &
" 369 (BC_1, *, internal, X)," &
" 370 (BC_1, *, internal, X)," &
" 371 (BC_1, *, internal, X)," &
" 372 (BC_1, *, controlr, 1)," &
" 373 (BC_1, IO75, output3, X, 372, 1, PULL1)," &
" 374 (BC_1, IO75, input, X)," &
" 375 (BC_1, *, controlr, 1)," &
" 376 (BC_1, IO76, output3, X, 375, 1, PULL1)," &
" 377 (BC_1, IO76, input, X)," &
" 378 (BC_1, *, controlr, 1)," &
" 379 (BC_1, IO78, output3, X, 378, 1, PULL1)," &
" 380 (BC_1, IO78, input, X)," &
" 381 (BC_1, *, internal, X)," &
" 382 (BC_1, *, internal, X)," &
" 383 (BC_1, *, internal, X)," &
" 384 (BC_1, *, controlr, 1)," &
" 385 (BC_1, IO79, output3, X, 384, 1, PULL1)," &
" 386 (BC_1, IO79, input, X)," &
" 387 (BC_1, *, controlr, 1)," &
" 388 (BC_1, IO80, output3, X, 387, 1, PULL1)," &
" 389 (BC_1, IO80, input, X)," &
" 390 (BC_1, *, controlr, 1)," &
" 391 (BC_1, IO81, output3, X, 390, 1, PULL1)," &
" 392 (BC_1, IO81, input, X)," &
" 393 (BC_1, *, internal, X)," &
" 394 (BC_1, *, internal, X)," &
" 395 (BC_1, *, internal, X)," &
" 396 (BC_1, *, controlr, 1)," &
" 397 (BC_1, IO82, output3, X, 396, 1, PULL1)," &
" 398 (BC_1, IO82, input, X)," &
" 399 (BC_1, *, controlr, 1)," &
" 400 (BC_1, IO83, output3, X, 399, 1, PULL1)," &
" 401 (BC_1, IO83, input, X)," &
" 402 (BC_1, *, controlr, 1)," &
" 403 (BC_1, IO84, output3, X, 402, 1, PULL1)," &
" 404 (BC_1, IO84, input, X)," &
" 405 (BC_1, *, internal, X)," &
" 406 (BC_1, *, internal, X)," &
" 407 (BC_1, *, internal, X)," &
" 408 (BC_1, *, controlr, 1)," &
" 409 (BC_1, IO85, output3, X, 408, 1, PULL1)," &
" 410 (BC_1, IO85, input, X)," &
" 411 (BC_1, *, controlr, 1)," &
" 412 (BC_1, IO86, output3, X, 411, 1, PULL1)," &
" 413 (BC_1, IO86, input, X)," &
-- INIT is not a compliance enable after configuration. For post-configuration
-- operation un-comment the next line and comment out the following line.
-- Repeat for registers 414 through 416.
-- " 414 (BC_1, *, controlr, 1)," &
" 414 (BC_1, *, internal, 1)," &
-- " 415 (BC_1, INIT, output3, X, 414, 1, PULL1)," &
" 415 (BC_1, *, internal, 0)," &
-- " 416 (BC_1, INIT, input, X)," &
" 416 (BC_1, *, internal, X)," &
" 417 (BC_1, *, internal, X)," &
" 418 (BC_1, *, internal, X)," &
" 419 (BC_1, *, internal, X)," &
" 420 (BC_1, *, controlr, 1)," &
" 421 (BC_1, IO90, output3, X, 420, 1, PULL1)," &
" 422 (BC_1, IO90, input, X)," &
" 423 (BC_1, *, controlr, 1)," &
" 424 (BC_1, IO91, output3, X, 423, 1, PULL1)," &
" 425 (BC_1, IO91, input, X)," &
" 426 (BC_1, *, controlr, 1)," &
" 427 (BC_1, IO92, output3, X, 426, 1, PULL1)," &
" 428 (BC_1, IO92, input, X)," &
" 429 (BC_1, *, internal, X)," &
" 430 (BC_1, *, internal, X)," &
" 431 (BC_1, *, internal, X)," &
" 432 (BC_1, *, controlr, 1)," &
" 433 (BC_1, IO93, output3, X, 432, 1, PULL1)," &
" 434 (BC_1, IO93, input, X)," &
" 435 (BC_1, *, controlr, 1)," &
" 436 (BC_1, IO94, output3, X, 435, 1, PULL1)," &
" 437 (BC_1, IO94, input, X)," &
" 438 (BC_1, *, controlr, 1)," &
" 439 (BC_1, IO95, output3, X, 438, 1, PULL1)," &
" 440 (BC_1, IO95, input, X)," &
" 441 (BC_1, *, internal, X)," &
" 442 (BC_1, *, internal, X)," &
" 443 (BC_1, *, internal, X)," &
" 444 (BC_1, *, controlr, 1)," &
" 445 (BC_1, IO96, output3, X, 444, 1, PULL1)," &
" 446 (BC_1, IO96, input, X)," &
" 447 (BC_1, *, controlr, 1)," &
" 448 (BC_1, IO97, output3, X, 447, 1, PULL1)," &
" 449 (BC_1, IO97, input, X)," &
" 450 (BC_1, *, controlr, 1)," &
" 451 (BC_1, IO98, output3, X, 450, 1, PULL1)," &
" 452 (BC_1, IO98, input, X)," &
" 453 (BC_1, *, internal, X)," &
" 454 (BC_1, *, internal, X)," &
" 455 (BC_1, *, internal, X)," &
" 456 (BC_1, *, controlr, 1)," &
" 457 (BC_1, IO99, output3, X, 456, 1, PULL1)," &
" 458 (BC_1, IO99, input, X)," &
" 459 (BC_1, *, controlr, 1)," &
" 460 (BC_1, IO101, output3, X, 459, 1, PULL1)," &
" 461 (BC_1, IO101, input, X)," &
" 462 (BC_1, *, internal, X)," &
" 463 (BC_1, *, internal, X)," &
" 464 (BC_1, *, internal, X)," &
" 465 (BC_1, *, internal, X)," &
" 466 (BC_1, *, internal, X)," &
" 467 (BC_1, *, internal, X)," &
" 468 (BC_1, *, controlr, 1)," &
" 469 (BC_1, IO102, output3, X, 468, 1, PULL1)," &
" 470 (BC_1, IO102, input, X)," &
" 471 (BC_1, *, controlr, 1)," &
" 472 (BC_1, IO103, output3, X, 471, 1, PULL1)," &
" 473 (BC_1, IO103, input, X)," &
" 474 (BC_1, *, internal, X)," &
" 475 (BC_1, *, internal, X)," &
" 476 (BC_1, *, internal, X)," &
" 477 (BC_1, *, internal, X)," &
" 478 (BC_1, *, internal, X)," &
" 479 (BC_1, *, internal, X)," &
" 480 (BC_1, *, controlr, 1)," &
" 481 (BC_1, IO104, output3, X, 480, 1, PULL1)," &
" 482 (BC_1, IO104, input, X)," &
" 483 (BC_1, *, controlr, 1)," &
" 484 (BC_1, IO105, output3, X, 483, 1, PULL1)," &
" 485 (BC_1, IO105, input, X)," &
" 486 (BC_1, *, controlr, 1)," &
" 487 (BC_1, IO106, output3, X, 486, 1, PULL1)," &
" 488 (BC_1, IO106, input, X)," &
" 489 (BC_1, *, internal, X)," &
" 490 (BC_1, *, internal, X)," &
" 491 (BC_1, *, internal, X)," &
" 492 (BC_1, *, controlr, 1)," &
" 493 (BC_1, IO107, output3, X, 492, 1, PULL1)," &
" 494 (BC_1, IO107, input, X)," &
" 495 (BC_1, *, controlr, 1)," &
" 496 (BC_1, IO108, output3, X, 495, 1, PULL1)," &
" 497 (BC_1, IO108, input, X)," &
" 498 (BC_1, *, internal, X)," &
" 499 (BC_1, *, internal, X)," &
" 500 (BC_1, *, internal, X)," &
" 501 (BC_1, *, internal, X)," &
" 502 (BC_1, *, internal, X)," &
" 503 (BC_1, *, internal, X)," &
" 504 (BC_1, *, controlr, 1)," &
" 505 (BC_1, IO113, output3, X, 504, 1, PULL1)," &
" 506 (BC_1, IO113, input, X)," &
" 507 (BC_1, *, controlr, 1)," &
" 508 (BC_1, IO114, output3, X, 507, 1, PULL1)," &
" 509 (BC_1, IO114, input, X)," &
" 510 (BC_1, *, internal, X)," &
" 511 (BC_1, *, internal, X)," &
" 512 (BC_1, *, internal, X)," &
" 513 (BC_1, *, internal, X)," &
" 514 (BC_1, *, internal, X)," &
" 515 (BC_1, *, internal, X)," &
" 516 (BC_1, *, controlr, 1)," &
" 517 (BC_1, IO115, output3, X, 516, 1, PULL1)," &
" 518 (BC_1, IO115, input, X)," &
" 519 (BC_1, *, controlr, 1)," &
" 520 (BC_1, IO116, output3, X, 519, 1, PULL1)," &
" 521 (BC_1, IO116, input, X)," &
" 522 (BC_1, *, controlr, 1)," &
" 523 (BC_1, IO117, output3, X, 522, 1, PULL1)," &
" 524 (BC_1, IO117, input, X)," &
" 525 (BC_1, *, internal, X)," &
" 526 (BC_1, *, internal, X)," &
" 527 (BC_1, *, internal, X)," &
" 528 (BC_1, *, controlr, 1)," &
" 529 (BC_1, IO118, output3, X, 528, 1, PULL1)," &
" 530 (BC_1, IO118, input, X)," &
" 531 (BC_1, *, controlr, 1)," &
" 532 (BC_1, IO119, output3, X, 531, 1, PULL1)," &
" 533 (BC_1, IO119, input, X)," &
" 534 (BC_1, *, controlr, 1)," &
" 535 (BC_1, IO120, output3, X, 534, 1, PULL1)," &
" 536 (BC_1, IO120, input, X)," &
" 537 (BC_1, *, internal, X)," &
" 538 (BC_1, *, internal, X)," &
" 539 (BC_1, *, internal, X)," &
" 540 (BC_1, *, controlr, 1)," &
" 541 (BC_1, IO122, output3, X, 540, 1, PULL1)," &
" 542 (BC_1, IO122, input, X)," &
" 543 (BC_1, *, controlr, 1)," &
" 544 (BC_1, IO123, output3, X, 543, 1, PULL1)," &
" 545 (BC_1, IO123, input, X)," &
" 546 (BC_1, *, internal, X)," &
" 547 (BC_1, *, internal, X)," &
" 548 (BC_1, *, internal, X)," &
" 549 (BC_1, *, internal, X)," &
" 550 (BC_1, *, internal, X)," &
" 551 (BC_1, *, internal, X)," &
" 552 (BC_1, *, controlr, 1)," &
" 553 (BC_1, IO124, output3, X, 552, 1, PULL1)," &
" 554 (BC_1, IO124, input, X)," &
" 555 (BC_1, *, controlr, 1)," &
" 556 (BC_1, IO125, output3, X, 555, 1, PULL1)," &
" 557 (BC_1, IO125, input, X)," &
" 558 (BC_1, *, controlr, 1)," &
" 559 (BC_1, IO126, output3, X, 558, 1, PULL1)," &
" 560 (BC_1, IO126, input, X)," &
" 561 (BC_1, *, internal, X)," &
" 562 (BC_1, *, internal, X)," &
" 563 (BC_1, *, internal, X)," &
" 564 (BC_1, *, controlr, 1)," &
" 565 (BC_1, IO127, output3, X, 564, 1, PULL1)," &
" 566 (BC_1, IO127, input, X)," &
" 567 (BC_1, *, controlr, 1)," &
" 568 (BC_1, IO128, output3, X, 567, 1, PULL1)," &
" 569 (BC_1, IO128, input, X)," &
" 570 (BC_1, *, controlr, 1)," &
" 571 (BC_1, IO129, output3, X, 570, 1, PULL1)," &
" 572 (BC_1, IO129, input, X)," &
" 573 (BC_1, *, internal, X)," &
" 574 (BC_1, *, internal, X)," &
" 575 (BC_1, *, internal, X)," &
" 576 (BC_1, *, controlr, 1)," &
" 577 (BC_1, IO130, output3, X, 576, 1, PULL1)," &
" 578 (BC_1, IO130, input, X)," &
" 579 (BC_1, *, controlr, 1)," &
" 580 (BC_1, IO131, output3, X, 579, 1, PULL1)," &
" 581 (BC_1, IO131, input, X)," &
" 582 (BC_1, *, internal, X)," &
" 583 (BC_1, *, internal, X)," &
" 584 (BC_1, *, internal, X)," &
" 585 (BC_1, *, internal, X)," &
" 586 (BC_1, *, internal, X)," &
" 587 (BC_1, *, internal, X)," &
" 588 (BC_1, *, controlr, 1)," &
" 589 (BC_1, IO134, output3, X, 588, 1, PULL1)," &
" 590 (BC_1, IO134, input, X)," &
" 591 (BC_1, *, controlr, 1)," &
" 592 (BC_1, IO135, output3, X, 591, 1, PULL1)," &
" 593 (BC_1, IO135, input, X)," &
" 594 (BC_1, *, internal, X)," &
" 595 (BC_1, *, internal, X)," &
" 596 (BC_1, *, internal, X)," &
" 597 (BC_1, *, internal, X)," &
" 598 (BC_1, *, internal, X)," &
" 599 (BC_1, *, internal, X)," &
" 600 (BC_1, *, controlr, 1)," &
" 601 (BC_1, IO136, output3, X, 600, 1, PULL1)," &
" 602 (BC_1, IO136, input, X)," &
" 603 (BC_1, *, controlr, 1)," &
" 604 (BC_1, IO137, output3, X, 603, 1, PULL1)," &
" 605 (BC_1, IO137, input, X)," &
" 606 (BC_1, *, internal, X)," &
" 607 (BC_1, *, internal, X)," &
" 608 (BC_1, *, internal, X)," &
" 609 (BC_1, *, internal, X)," &
" 610 (BC_1, *, internal, X)," &
" 611 (BC_1, *, internal, X)," &
" 612 (BC_1, *, controlr, 1)," &
" 613 (BC_1, IO138, output3, X, 612, 1, PULL1)," &
" 614 (BC_1, IO138, input, X)," &
" 615 (BC_1, *, controlr, 1)," &
" 616 (BC_1, IO139, output3, X, 615, 1, PULL1)," &
" 617 (BC_1, IO139, input, X)," &
" 618 (BC_1, *, controlr, 1)," &
" 619 (BC_1, IO140, output3, X, 618, 1, PULL1)," &
" 620 (BC_1, IO140, input, X)," &
" 621 (BC_1, *, internal, X)," &
" 622 (BC_1, *, internal, X)," &
" 623 (BC_1, *, internal, X)," &
" 624 (BC_1, *, controlr, 1)," &
" 625 (BC_1, IO141, output3, X, 624, 1, PULL1)," &
" 626 (BC_1, IO141, input, X)," &
" 627 (BC_1, *, controlr, 1)," &
" 628 (BC_1, IO142, output3, X, 627, 1, PULL1)," &
" 629 (BC_1, IO142, input, X)," &
" 630 (BC_1, *, controlr, 1)," &
" 631 (BC_1, IO143, output3, X, 630, 1, PULL1)," &
" 632 (BC_1, IO143, input, X)," &
" 633 (BC_1, *, internal, X)," &
" 634 (BC_1, *, internal, X)," &
" 635 (BC_1, *, internal, X)," &
" 636 (BC_1, *, controlr, 1)," &
" 637 (BC_1, IO145, output3, X, 636, 1, PULL1)," &
" 638 (BC_1, IO145, input, X)," &
" 639 (BC_1, *, controlr, 1)," &
" 640 (BC_1, IO146, output3, X, 639, 1, PULL1)," &
" 641 (BC_1, IO146, input, X)," &
" 642 (BC_1, *, controlr, 1)," &
" 643 (BC_1, IO147, output3, X, 642, 1, PULL1)," &
" 644 (BC_1, IO147, input, X)," &
" 645 (BC_1, *, internal, X)," &
" 646 (BC_1, *, internal, X)," &
" 647 (BC_1, *, internal, X)," &
" 648 (BC_1, *, controlr, 1)," &
" 649 (BC_1, IO148, output3, X, 648, 1, PULL1)," &
" 650 (BC_1, IO148, input, X)," &
" 651 (BC_1, *, controlr, 1)," &
" 652 (BC_1, IO149, output3, X, 651, 1, PULL1)," &
" 653 (BC_1, IO149, input, X)," &
" 654 (BC_1, *, controlr, 1)," &
" 655 (BC_1, IO150, output3, X, 654, 1, PULL1)," &
" 656 (BC_1, IO150, input, X)," &
" 657 (BC_1, *, internal, X)," &
" 658 (BC_1, *, internal, X)," &
" 659 (BC_1, *, internal, X)," &
" 660 (BC_1, *, controlr, 1)," &
" 661 (BC_1, IO151, output3, X, 660, 1, PULL1)," &
" 662 (BC_1, IO151, input, X)," &
" 663 (BC_1, *, controlr, 1)," &
" 664 (BC_1, IO152, output3, X, 663, 1, PULL1)," &
" 665 (BC_1, IO152, input, X)," &
" 666 (BC_1, *, internal, X)," &
" 667 (BC_1, *, internal, X)," &
" 668 (BC_1, *, internal, X)," &
" 669 (BC_1, *, internal, X)," &
" 670 (BC_1, *, internal, X)," &
" 671 (BC_1, *, internal, X)," &
" 672 (BC_1, *, internal, X)";
--end boundary register
attribute DESIGN_WARNING of XC5206_TQ176 : entity is
"CCLK and DONE are not represented in BOUNDARY_REGISTER." &
"This BSDL file must be modified by the FPGA designer in order to" &
"reflect post-configuration behavior (if any)." &
"If INIT has been high or floating since power-on or the last" &
"rising edge of PROGRAM, then the device may be in" &
"configuration mode in which case this file is not valid." &
"Programmably inverted input paths are controlled with the" &
"wrong polarity." &
"The tristate control is not captured properly when GTS is activated." &
"Some pins have both controlled and uncontrolled input paths.";
end XC5206_TQ176;